Dell PowerVault 56F Dell PowerVault 56F 16-Port Fibre Channel Switch Inst - Page 140

portLogShow, LSDbAllShow, nbrStateShow, portDisable, portEnable, ucastAllShow, LSDAllShow, <queue

Get Dell PowerVault 56F PDF manuals and user guides View all Dell PowerVault 56F manuals
Add to My Manuals
Save this manual to your list of manuals

Page 140 highlights

REMPORT (3) SPFCOST (3) NBFSM NGBRSTATE (2) UCAST ADDPATH (1) RELICPDB (2) SPFCOST(3) MQ QREAD (1) QWRITE (1) SYS NOMEM (1) SYSCALL (2) TIMERS ENQFAIL (1) MSG (3) Removing an entry from a multicast routing table failed. An error occurred with computing the multicast path tree. An error occurred in the neighbor Finite State. A static path configuration failed. The path selection task received an E_Port SCN, but the port was already ISL. An error occurred with computing the unicast path tree. A task was unable to receive a message. A task was not able to post a message on a queue. The system's memory is exhausted. A system call into VxWorks failed. An error occurred while setting a timer. The timer task received an unknown message. Run the portLogShow command. Contact Customer Support. Run the LSDbAllShow command. Contact Customer Support. Check the neighbor's state with the nbrStateShow command. If the state is not NB_ST_FULL, force a state change with the portDisable command followed by portEnable. After a few seconds, if the state is not NB_ST_FULL, reboot both the local and remote switches. Check command parameters. Run the ucastAllShow command. Contact customer support. Run the LSDAllShow command. Contact customer support. Run the command show with the ID of the queue reported in the error. Contact customer support. See "MQ-QWRITE Error" found later in this chapter for more information. Reboot the switch. Contact customer support. Reboot the switch. Contact customer support. Reboot the switch. Run the commands actTimersShow and timerShow . Contact customer support. Contact customer support. A-4 Installation and Troubleshooting Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
A-4
Installation and Troubleshooting Guide
REMPORT (3)
Removing an entry from a multi-
cast routing table failed.
Run the
portLogShow
command. Con-
tact Customer Support.
SPFCOST (3)
An error occurred with comput-
ing the multicast path tree.
Run the
LSDbAllShow
command. Con-
tact Customer Support.
NBFSM
NGBRSTATE
(2)
An error occurred in the neighbor
Finite State.
Check the neighbor
’
s state with the
nbrStateShow
command.
If the state is not NB_ST_FULL, force a
state change with the
portDisable
com-
mand followed by
portEnable
.
After a few seconds, if the state is not
NB_ST_FULL, reboot both the local and
remote switches.
UCAST
ADDPATH (1)
A static path configuration failed.
Check command parameters.
RELICPDB (2)
The path selection task received
an E_Port SCN, but the port was
already ISL.
Run the
ucastAllShow
command. Con-
tact customer support.
SPFCOST(3)
An error occurred with comput-
ing the unicast path tree.
Run the
LSDAllShow
command. Contact
customer support.
MQ
QREAD (1)
A task was unable to receive a
message.
Run the command
show
<queue ID>
with the ID of the queue reported in the
error. Contact customer support.
QWRITE (1)
A task was not able to post a
message on a queue.
See
“
MQ-QWRITE Error
”
found later in
this chapter for more information.
SYS
NOMEM (1)
The system
’
s memory is
exhausted.
Reboot the switch. Contact customer
support.
SYSCALL (2)
A system call into VxWorks
failed.
Reboot the switch. Contact customer
support.
TIMERS
ENQFAIL (1)
An error occurred while setting a
timer.
Reboot the switch. Run the commands
actTimersShow
and
timerShow
<timer ID>
. Contact customer support.
MSG (3)
The timer task received an
unknown message.
Contact customer support.
È¿ÉÀ¶·0¹¸º··+µµ¼µË
±²³´µ¶·µ¸¹º»
À¾Ëôµ
"ÎξÎ
ºµ*µÎ¼·¸
"Á¹´²¿²·¼¾¿
)»·¼¾¿