Home » Fujitsu Manuals » Hard Drives » Fujitsu MPD3173AT » Manual Viewer

Fujitsu MPD3173AT Product Manual - Page 21

Table 1.3, Current and power dissipation

Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

(3) Current Requirements and Power Dissipation Table 1.3 lists the current and power dissipation. Table 1.3 Current and power dissipation Mode of Operation Typical RMS current (*1) [mA] +12 V +5 V Typical Power (*2) [watts] Model MPD3043 MPD3064/ MPD3108/ MPD3173 All Models MPD3043 MPD3064/ MPD3108/ MPD3173 AT MPD3084 MPD3130 AT AT MPD3084 MPD3130 AT AT AT AT AT Spin up 1500 1500 1600 1600 560 20.8 20.8 22.0 22.0 1900 peak 1900 peak 1900 peak 1900 peak 600 peak Idle (Ready) (*3) 130 177 205 230 280 3.0 3.5 3.8 4.2 R/W (On Track) (*4) 168 213 240 267 560 4.8 5.4 5.7 6.0 Seek (Random) (*5) 325 350 377 404 544 6.6 6.9 7.2 7.6 Standby 6.5 6.5 6.5 6.5 157 0.9 0.9 0.9 0.9 Sleep 6.5 6.5 6.5 6.5 152 0.8 0.8 0.8 0.8 *1 Current is typical rms except for spin up. *2 Power requirements reflect nominal values for +12V and +5V power. *3 Idle mode is in effect when the drive is not reading, writing, seeking, or executing any commands. A portion of the R/W circuitry is powered down, the spindle motor is up to speed and the Drive ready condition exists. *4 R/W mode is defined as 50% read operations and 50% write operations on a single physical track. *5 Seek mode is defined as continuous random seek operations with minimum controller delay. 1 - 6 C141-E069-02EN

Section	Page
Front title	1
PREFACE	4
CONTENTS	8
FIGURES	12
TABLES	14
CHAPTER 1 DEVICE OVERVIEW	16
1.1 Features	16
1.1.1 Functions and performance	16
1.1.2 Adaptability	17
1.1.3 Interface	17
1.2 Device Specifications	19
1.2.1 Specifications summary	19
1.2.2 Model and product number	20
1.3 Power Requirements	20
1.4 Environmental Specifications	23
1.5 Acoustic Noise	23
1.6 Shock and Vibration	24
1.7 Reliability	24
1.8 Error Rate	25
1.9 Media Defects	25
CHAPTER 2 DEVICE CONFIGURATION	26
2.1 Device Configuration	26
2.2 System Configuration	28
2.2.1 ATA interface	28
2.2.2 1 drive connection	28
2.2.3 2 drives connection	28
CHAPTER 3 INSTALLATION CONDITIONS	30
3.1 Dimensions	30
3.2 Mounting	32
3.3 Cable Connections	36
3.3.1 Device connector	36
3.3.2 Cable connector specifications	37
3.3.3 Device connection	37
3.3.4 Power supply connector (CN1)	38
3.3.5 System configuration for Ultra DMA	38
3.4 Jumper Settings	41
3.4.1 Location of setting jumpers	41
3.4.2 Factory default setting	42
3.4.3 Jumper configuration	42
CHAPTER 4 THEORY OF DEVICE OPERATION	46
4.1 Outline	46
4.2 Subassemblies	46
4.2.1 Disk	46
4.2.2 Head	47
4.2.3 Spindle	49
4.2.4 Actuator	49
4.2.5 Air filter	49
4.3 Circuit Configuration	50
4.4 Power-on Sequence	52
4.5 Self-calibration	54
4.5.1 Self-calibration contents	54
4.5.2 Execution timing of self-calibration	55
4.5.3 Command processing during self-calibration	55
4.6 Read/write Circuit	56
4.6.1 Read/write preamplifier (PreAMP)	56
4.6.2 Write circuit	56
4.6.3 Read circuit	58
4.6.4 Time base generator circuit	59
4.7 Servo Control	59
4.7.1 Servo control circuit	60
4.7.2 Data-surface servo format	63
4.7.3 Servo frame format	63
4.7.4 Actuator motor control	65
4.7.5 Spindle motor control	66
CHAPTER 5 INTERFACE	68
5.1 Physical Interface	69
5.1.1 Interface signals	69
5.1.2 Signal assignment on the connector	70
5.2 Logical Interface	73
5.2.1 I/O registers	73
5.2.2 Command block registers	75
5.2.3 Control block registers	80
5.3 Host Commands	80
5.3.1 Command code and parameters	81
5.3.2 Command descriptions	83
5.3.3 Error posting	133
5.4 Command Protocol	134
5.4.1 Data transferring commands from device to host	134
5.4.2 Data transferring commands from host to device	136
5.4.3 Commands without data transfer	138
5.4.4 Other commands	139
5.4.5 DMA data transfer commands	139
5.5 Ultra DMA feature set	141
5.5.1 Overview	141
5.5.2 Phases of operation	142
5.5.3 Ultra DMA data in commands	142
5.5.3.1 Initiating an Ultra DMA data in burst	142
5.5.3.2 The data in transfer	143
5.5.3.3 Pausing an Ultra DMA data in burst	143
5.5.3.4 Terminating an Ultra DMA data in burst	144
5.5.4 Ultra DMA data out commands	146
5.5.4.1 Initiating an Ultra DMA data out burst	146
5.5.4.2 The data out transfer	147
5.5.4.3 Pausing an Ultra DMA data out burst	147
5.5.4.4 Terminating an Ultra DMA data out burst	148
5.5.5 Ultra DMA CRC rules	150
5.5.6 Series termination required for Ultra DMA	151
5.6 Timing	152
5.6.1 PIO data transfer	152
5.6.2 Multiword data transfer	153
5.6.3 Ultra DMA data transfer	154
5.6.3.1 Initiating an Ultra DMA data in burst	154
5.6.3.2 Ultra DMA data burst timing requirements	155
5.6.3.3 Sustained Ultra DMA data in burst	157
5.6.3.4 Host pausing an Ultra DMA data in burst	158
5.6.3.5 Device terminating an Ultra DMA data in burst	159
5.6.3.6 Host terminating an Ultra DMA data in burst	160
5.6.3.7 Initiating an Ultra DMA data out burst	161
5.6.3.8 Sustained Ultra DMA data out burst	162
5.6.3.9 Device pausing an Ultra DMA data out burst	163
5.6.3.10 Host terminating an Ultra DMA data out burst	164
5.6.3.11 Device terminating an Ultra DMA data in burst	165
5.6.4 Power-on and reset	166
CHAPTER 6 OPERATIONS	168
6.1 Device Response to the Reset	168
6.1.1 Response to power-on	169
6.1.2 Response to hardware reset	170
6.1.3 Response to software reset	171
6.1.4 Response to diagnostic command	172
6.2 Address Translation	173
6.2.1 Default parameters	173
6.2.2 Logical address	174
6.3 Power Save	175
6.3.1 Power save mode	175
6.3.2 Power commands	177
6.4 Defect Management	177
6.4.1 Spare area	178
6.4.2 Alternating defective sectors	178
6.5 Read-Ahead Cache	180
6.5.1 Data buffer configuration	180
6.5.2 Caching operation	181
6.5.3 Usage of read segment	182
6.6 Write Cache	187
Addresses	189
Reader Comment Form	190

Match case Limit results 1 per page

C141-E069-02EN

1 - 6

(3)

Current Requirements and Power Dissipation

Table 1.3 lists the current and power dissipation.

Table 1.3

Current and power dissipation

Typical RMS current (*1) [mA]

+12 V

+5 V

Model

MPD3043

MPD3064/

MPD3084

MPD3108/

MPD3130

MPD3173

All Models

MPD3043

MPD3064/

MPD3084

MPD3108/

MPD3130

MPD3173

Spin up

1500

1900 peak

1500

1900 peak

1600

1900 peak

1600

1900 peak

560

600 peak

20.8

22.0

Idle (Ready)

(*3)

130

177

205

230

280

3.0

3.5

3.8

4.2

R/W (On Track)

(*4)

168

213

240

267

560

4.8

5.4

5.7

6.0

Seek (Random)

(*5)

325

350

377

404

544

6.6

6.9

7.2

7.6

Standby

6.5

157

0.9

Sleep

6.5

152

0.8

Current is typical rms except for spin up.

Power requirements reflect nominal values for +12V and +5V power.

Idle mode is in effect when the drive is not reading, writing, seeking, or executing any commands.

A portion of the R/W circuitry is powered

down, the spindle motor is up to speed and the Drive ready condition exists.

R/W mode is defined as 50% read operations and 50% write operations on a single physical track.

Seek mode is defined as continuous random seek operations with minimum controller delay.

Typical Power (*2)

[watts]

Mode of Operation