Garmin GPSMAP 60CSx Owner's Manual - Page 12

Installing the Batteries, To install the Lanyard - microsd

Get Garmin GPSMAP 60CSx - Hiking GPS Receiver PDF manuals and user guides
UPC - 753759049126
View all Garmin GPSMAP 60CSx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Getting Started > Unit Overview Installing the Batteries The GPSMAP 60CSx operates on two AA batteries (not included), which are located in the back of the unit. You can use Alkaline or NiMH batteries. See page 67 to set the battery type. To install the batteries: 1. Remove the battery cover by turning the D-Ring 1/4 turn counterclockwise and pulling the cover loose. USE BY 2009 USE BY 2009 2. Insert the batteries, observing the proper polarity. A polarity diagram is molded into the battery compartment. Battery 3. Reinstall the battery Compartment cover by aligning the back cover with the unit and turning the D-Ring 1/4 turn clockwise. Remove the batteries from your GPSMAP 60CSx when you do not expect to use the unit for several months. Data is not lost when batteries are removed.  Note: Lithium batteries are not recommended because the initial voltage of new batteries may exceed 1.5 volts each, which may cause the GPSMAP 60CSx to turn off. To install the Lanyard: 1. Place the loop of the Lanyard through the slot at the at the upper left side of the unit. 2 Route the strap through the loop and pull tight. Wrist Strap Installation Refer to page 9 for information on accessing the microSD data card in the battery compartment. GPSMAP 60CSx Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
²
GPSMAP 60CSx Owner’s Manual
G
ETTING
S
TARTED
>
U
NIT
O
VERVIEW
Installing the Batteries
The GPSMAP 60CSx operates on two AA batteries
(not included), which are located in the back of the
unit. You can use Alkaline or NiMH batteries. See
page 67
to set the battery type.
To install the batteries:
1.
Remove the battery
cover by turning the
D-Ring 1/4 turn counter-
clockwise and pulling the
cover loose.
2.
Insert the batteries,
observing the proper
polarity. A polarity
diagram is molded into
the battery compartment.
3.
Reinstall the battery
cover by aligning the
back cover with the unit and turning the D-Ring
1/4 turn clockwise.
Remove the batteries from your GPSMAP 60CSx
when you do not expect to use the unit for several
months. Data is not lost when batteries are removed.
NOTE:
Lithium batteries are not recommended
because the initial voltage of new batteries may
exceed 1.5 volts each, which may cause the
GPSMAP 60CSx to turn off.
To install the Lanyard:
1.
Place the loop of the Lanyard through the slot
at the at the upper left side of the unit.
2
Route the strap through the loop and pull tight.
Wrist Strap
Installation
Refer to
page 9
for information on accessing the
microSD data card in the battery compartment.
Battery
Compartment
USE BY 2009
USE BY 2009
Battery
Compartment