HP 400N HP JetDirect 400N Print Server Hardware Installation Guide - 5969-3587 - Page 55

Configuring Novell NetWare Source Routing (Token Ring Cards Only), To con NetWare source routing

Get HP 400N - JetDirect MIO Print Server PDF manuals and user guides
UPC - 088698733714
View all HP 400N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Configuring Novell NetWare Source Routing (Token Ring Cards Only) You can select the method for Novell NetWare Token Ring source routing from the control panel. The possible routing methods are: • AUTO (default): Source routing is enabled if necessary. • OFF: All packets are sent without source routing-packets are received only if they originate from the same ring. • SINGLE R: All packets are sent with source routing. The Single Route method is used for broadcasts and when the route is unknown. • ALL RT: All packets are sent with source routing. The All Routes method is used for broadcasts and when the route is unknown. You can configure the NetWare source routing if NetWare is enabled and you have installed a Token Ring print server. To configure NetWare source routing NOTE For HP 2500C/CM Professional Series and DesignJet ColorPro GA printers, see the "HP 2500C/CM Professional Series and DesignJet ColorPro GA Control Panel" instructions at the end of this chapter. If you have not already done so, enable Novell NetWare (IPX/ SPX=ON*) by following the instructions described in "To enable or disable network protocols" in this chapter. 1. Take the printer offline by pressing [On Line] or [Go] to indicate offline. 2. Press [Menu] repeatedly until the following message is displayed on the control panel: 4 Series printers AUX IO MENU 4 Plus and 4V Series printers MIO MENU Color LaserJet printers (Proceed to Step 4) MIO CONFIG MENU CFG NETWORK=NO * Printer Control 3 Panel Using the Control Panel for Printers 3-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Using the Control Panel for Printers 3-7
3
Printer Control
Panel
Configuring Novell NetWare Source
Routing (Token Ring Cards Only)
You can select the method for Novell NetWare Token Ring source
routing from the control panel. The possible routing methods are:
•
AUTO
(default):
Source routing is enabled if necessary.
•
OFF:
All packets are sent without source routing
—
packets are
received only if they originate from the same ring.
•
SINGLE R:
All packets are sent with source routing. The
Single
Route
method is used for broadcasts and when the route is
unknown.
•
ALL RT:
All packets are sent with source routing. The
All
Routes
method is used for broadcasts and when the route is
unknown.
You can configure the NetWare source routing if NetWare is
enabled and you have installed a Token Ring print server.
To configure NetWare source routing
NOTE
For HP 2500C/CM Professional Series and
DesignJet ColorPro GA printers, see the
“
HP
2500C/CM Professional Series and DesignJet
ColorPro GA Control Panel
”
instructions at the end
of this chapter.
If you have not already done so, enable Novell NetWare (
IPX/
SPX=ON*
) by following the instructions described in
“
To enable
or disable network protocols
”
in this chapter.
1.
Take the printer offline by pressing
[On°Line]
or
[Go]
to indicate
offline.
2.
Press
[Menu]
repeatedly until the following message is displayed
on the control panel:
4 Series printers
AUX IO MENU
4 Plus and 4V Series printers
MIO MENU
Color LaserJet printers
(
Proceed to Step 4
)
MIO CONFIG MENU
CFG NETWORK=NO *