HP 400N HP JetDirect 400N Print Server Hardware Installation Guide - 5969-3587 - Page 76

Configuring Novell NetWare Source Routing, Token Ring Card Only, default, SINGLE R, ALL RT

Get HP 400N - JetDirect MIO Print Server PDF manuals and user guides
UPC - 088698733714
View all HP 400N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

Configuring Novell NetWare Source Routing (Token Ring Card Only) You can select the method for Novell NetWare source routing from the control panel. The possible routing methods are: • AUTO (default): Source routing will be enabled on a packet- by-packet basis. • OFF: All packets are sent without source routing-that is, packets must be from the same ring. • SINGLE R: Source routing used for all packets sent. The Single Route method is used for broadcasts and when the route is unknown. • ALL RT: Source routing used for all packets sent. The All Routes method is used for broadcasts and when the route is unknown. You can configure the NetWare source routing only if NetWare is enabled and you have installed a token ring network interface. To configure NetWare source routing If you haven't already done so, enable Novell NetWare by following the instructions described in "To enable or disable network protocols" in this chapter. For the 600 Series Printers 1. Access the configuration menu (see "To enable or disable network protocols" in this chapter). 2. Access the Novell menu by pressing [Enter], then ↑ , then [Enter]. MIO SETUP and CFG IPX/SPX=YES→ appear. 3. Press ↑ until the current source routing appears. MIO SETUP and SRC RT=→ appear. 4. To maintain the current setting, press ↑ . 5. To change source routing, proceed as follows: a. To display the current source routing, press [Enter]. b. Press ↑ until the source routing that you want appears. c. To save the new source routing, press [Enter]. 4-8 Control Panel for Large-Format Printers

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
4-8
Control Panel for Large-Format Printers
Configuring Novell NetWare Source Routing
(Token Ring Card Only)
You can select the method for Novell NetWare source routing from
the control panel. The possible routing methods are:
•
AUTO
(default):
Source routing will be enabled on a packet-
by-packet basis.
•
OFF:
All packets are sent without source routing
—
that is,
packets must be from the same ring.
•
SINGLE R:
Source routing used for all packets sent. The
Single Route
method is used for broadcasts and when the
route is unknown.
•
ALL RT:
Source routing used for all packets sent. The
All
Routes
method is used for broadcasts and when the route
is unknown.
You can configure the NetWare source routing only if NetWare is
enabled and you have installed a token ring network interface.
To configure NetWare source routing
If you haven
’
t already done so, enable Novell NetWare by following
the instructions described in
“
To enable or disable network
protocols
”
in this chapter.
For the 600 Series Printers
1.
Access the configuration menu (see
“
To enable or disable
network protocols
”
in this chapter).
2.
Access the Novell menu by pressing
[Enter]
, then
↑
, then
[Enter]
.
MIO SETUP
and
CFG IPX/SPX=YES
→
appear.
3.
Press
↑
until the current source routing appears.
MIO SETUP
and
SRC RT=<current source routing>
→
appear.
4.
To maintain the current setting, press
↑
.
5.
To change source routing, proceed as follows:
a. To display the current source routing, press
[Enter]
.
b. Press
↑
until the source routing that you want appears.
c. To save the new source routing, press
[Enter]
.