HP 400N HP JetDirect 400N Print Server Hardware Installation Guide - 5969-3587 - Page 60

Configuring Apple EtherTalk Phase Parameters (Ethernet Cards Only), To con EtherTalk parameters

Get HP 400N - JetDirect MIO Print Server PDF manuals and user guides
UPC - 088698733714
View all HP 400N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Configuring Apple EtherTalk Phase Parameters (Ethernet Cards Only) You can configure Apple EtherTalk parameters if the Apple EtherTalk protocol is enabled (ETALK=ON*), and the PostScript printer language is enabled. To ensure the PostScript printer language is enabled, check the Configuration Menu (for 5Si Series printers) or the JOB MENU (for other printers). PERSONALTY=PS* or PERSONALTY=AUTO* should be set. To configure EtherTalk parameters NOTE For HP 2500C/CM Professional Series and DesignJet ColorPro GA printers, see the "HP 2500C/CM Professional Series and DesignJet ColorPro GA Control Panel" instructions at the end of this chapter. If you haven't already done so, enable EtherTalk by following the instructions described in "To enable or disable network protocols" in this chapter. 1. Take the printer offline by pressing [On Line] or [Go] to indicate offline. 2. Press [Menu] repeatedly until the following message is displayed on the control panel: 4 Series printers AUX IO MENU 4 Plus and 4V Series printers MIO MENU Color LaserJet printers (Proceed to Step 4) MIO CONFIG MENU CFG NETWORK=NO * 4Si Series printers (select the MIO MENU 1 or card slot being configured) MIO MENU 2 5Si Series printers (select the HP MIO 1 MENU or card slot being configured) HP MIO 2 MENU 5 Series printers HP MIO MENU 3. Press [Item] until CFG NETWORK=NO* appears. 3-12 Using the Control Panel for Printers

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
3-12
Using the Control Panel for Printers
Configuring Apple EtherTalk Phase
Parameters (Ethernet Cards Only)
You can configure Apple EtherTalk parameters if the Apple
EtherTalk protocol is enabled (
ETALK=ON*
), and the PostScript
printer language is enabled.
To ensure the PostScript printer language is enabled, check the
Configuration Menu
(for 5Si Series printers) or the
JOB MENU
(for other printers).
PERSONALTY=PS*
or
PERSONALTY=AUTO*
should be set.
To configure EtherTalk parameters
NOTE
For HP 2500C/CM Professional Series
and DesignJet ColorPro GA printers, see the
“
HP 2500C/CM Professional Series and DesignJet
ColorPro GA Control Panel
”
instructions at the
end of this chapter.
If you haven
’
t already done so, enable EtherTalk by following the
instructions described in
“
To enable or disable network protocols
”
in this chapter.
1.
Take the printer offline by pressing
[On°Line]
or
[Go]
to indicate
offline.
2.
Press
[Menu]
repeatedly until the following message is displayed
on the control panel:
3.
Press
[Item]
until
CFG NETWORK=NO*
appears.
4 Series printers
AUX IO MENU
4 Plus and 4V Series printers
MIO MENU
Color LaserJet printers
(
Proceed to Step 4
)
MIO CONFIG MENU
CFG NETWORK=NO *
4Si Series printers (select the
card slot being configured)
MIO MENU 1
or
MIO MENU 2
5Si Series printers (select the
card slot being configured)
HP MIO 1 MENU
or
HP MIO 2 MENU
5 Series printers
HP MIO MENU