HP 400N HP JetDirect 400N Print Server Hardware Installation Guide - 5969-3587 - Page 58

To con TCP/IP parameters, CAUTION

Get HP 400N - JetDirect MIO Print Server PDF manuals and user guides
UPC - 088698733714
View all HP 400N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

To configure TCP/IP parameters NOTE For HP 2500C/CM Professional Series and DesignJet ColorPro GA printers, see the "HP 2500C/CM Professional Series and DesignJet ColorPro GA Control Panel" instructions at the end of this chapter. If you have not already done so, enable TCP/IP (TCP/IP=ON*) by following the instructions described in "To enable or disable network protocols" in this chapter. CAUTION Enter data carefully. If you make an incorrect entry, you cannot change it without starting again from step 1. 1. Take the printer offline by pressing [On Line] or [Go] to indicate offline. 2. Press [Menu] repeatedly until the following message is displayed on the control panel: 4 Series printers AUX IO MENU 4 Plus and 4V Series printers MIO MENU Color LaserJet printers (Proceed to Step 4) MIO CONFIG MENU CFG NETWORK=NO * 4Si Series printers (select the MIO MENU 1 or card slot being configured) MIO MENU 2 5Si Series printers (select the HP MIO 1 MENU or card slot being configured) HP MIO 2 MENU 5 Series printers HP MIO MENU 3. Press [Item] until CFG NETWORK=NO* appears. 4. Change the message to CFG NETWORK=YES* using the following buttons: 5 Series and 5Si Series printers Press [+], then [Select] Other printers Press [+], then [Enter] 5. Press [Item] until CFG TCP/IP=NO* appears. 3-10 Using the Control Panel for Printers

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
3-10
Using the Control Panel for Printers
To configure TCP/IP parameters
NOTE
For HP 2500C/CM Professional Series
and DesignJet ColorPro GA printers, see the
“
HP 2500C/CM Professional Series and DesignJet
ColorPro GA Control Panel
”
instructions at the
end of this chapter.
If you have not already done so, enable TCP/IP (
TCP/IP=ON*
)
by following the instructions described in
“
To enable or disable
network protocols
”
in this chapter.
CAUTION
Enter data carefully. If you make an incorrect entry,
you cannot change it without starting again from
step 1.
1.
Take the printer offline by pressing
[On°Line]
or
[Go]
to indicate
offline.
2.
Press
[Menu]
repeatedly until the following message is displayed
on the control panel:
3.
Press
[Item]
until
CFG NETWORK=NO*
appears.
4.
Change the message to
CFG NETWORK=YES*
using the following
buttons:
5.
Press
[Item]
until
CFG TCP/IP=NO*
appears.
4 Series printers
AUX IO MENU
4 Plus and 4V Series printers
MIO MENU
Color LaserJet printers
(
Proceed to Step 4
)
MIO CONFIG MENU
CFG NETWORK=NO *
4Si Series printers (select the
card slot being configured)
MIO MENU 1
or
MIO MENU 2
5Si Series printers (select the
card slot being configured)
HP MIO 1 MENU
or
HP MIO 2 MENU
5 Series printers
HP MIO MENU
5 Series and 5Si Series printers
Press
[+]
, then
[Select]
±
Other printers
Press
[+]
, then
[Enter]
±