HP 400N HP JetDirect 400N Print Server Hardware Installation Guide - 5969-3587 - Page 81

Configuring Apple EtherTalk Phase Parameters (Ethernet Cards Only

Get HP 400N - JetDirect MIO Print Server PDF manuals and user guides
UPC - 088698733714
View all HP 400N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

Configuring Apple EtherTalk Phase Parameters (Ethernet Cards Only) NOTE EtherTalk is supported by HP DesignJet 650C, Series 700, and 2500CP series printers with PostScript modules installed. You can set Apple EtherTalk parameters if the Apple EtherTalk protocol and the PostScript printer language are enabled (Lang=Postscript→). To configure EtherTalk parameters If you haven't already done so, enable EtherTalk by following the instructions described in "To enable or disable network protocols" in this chapter. For the 600 Series Printers 1. Access the configuration menu (see "To enable or disable network protocols" in this chapter). 2. To access the EtherTalk menu, press [Enter], then ↑, then [Enter]. MIO SETUP and CFG ETALK=YES→ appear. 3. Press ↑ . ETALK PHASE=→ appears. 4. To maintain the current value, press ↑. 5. To change value, proceed as follows: a. Press [Enter] to display the current value. b. Press ↑ until the value that you want appears. c. Press [Enter] to save the new value. MIO SETUP and ETALK PHASE=→ appear. d. Press ↑ to continue. 6. Press [Previous] until Ready to plot is displayed. HP DesignJet 4 Control Panel Control Panel for Large-Format Printers 4-13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Control Panel for Large-Format Printers 4-13
4
HP DesignJet
Control Panel
Configuring Apple EtherTalk Phase
Parameters (Ethernet Cards Only)
NOTE
EtherTalk is supported by HP DesignJet 650C,
Series 700, and 2500CP series printers with
PostScript modules installed.
You can set Apple EtherTalk parameters if the Apple EtherTalk
protocol and the PostScript printer language are enabled
(
Lang=Postscript
→
).
To configure EtherTalk parameters
If you haven
’
t already done so, enable EtherTalk by following the
instructions described in
“
To enable or disable network protocols
”
in this chapter.
For the 600 Series Printers
1.
Access the configuration menu (see
“
To enable or disable
network protocols
”
in this chapter).
2.
To access the EtherTalk menu, press
[Enter]
, then
↑
, then
[Enter]
.
MIO SETUP
and
CFG ETALK=YES
→
appear.
3.
Press
↑
.
ETALK PHASE=<current value>
→
appears.
4.
To maintain the current value, press
↑
.
5.
To change value, proceed as follows:
a. Press
[Enter]
to display the current value.
b. Press
↑
until the value that you want appears.
c. Press
[Enter]
to save the new value.
MIO SETUP
and
ETALK PHASE=<new value>
→
appear.
d. Press
↑
to continue.
6.
Press
[Previous]
until
Ready to plot
is displayed.