HP 400N HP JetDirect 400N Print Server Hardware Installation Guide - 5969-3587 - Page 59

Printer Control, Panel, CFG TCP/IP=YES, BOOTP=YES, BOOTP=NO, IP BYTE 1=<value&gt

Get HP 400N - JetDirect MIO Print Server PDF manuals and user guides
UPC - 088698733714
View all HP 400N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

6. Change this to CFG TCP/IP=YES* by pressing [+], and then pressing [Select] or [Enter] depending on your printer model. 7. Press [Item] until BOOTP=YES* or BOOTP=NO* appears. • The asterisk (*) indicates the active selection. • To change the BOOTP= setting, press [+]. Then press [Select] or [Enter] depending on your printer model. Be sure "*" appears alongside your selection. If BOOTP=YES*, the printer is configured to retrieve its TCP/IP parameters over the network using BOOTP or DHCP. No other TCP/IP prompts will be displayed on the printer's control panel. To activate the printer and save your changes, press [OnLine] or [Go] depending on your printer model. If BOOTP=NO *, the printer is configured to accept TCP/IP parameters from the printer's control panel. Press [Item] to configure each TCP/IP parameter. IP BYTE 1=* should appear on the control panel first. Continue with step 8. 8. To enter the first byte of the IP address, use the [+], [-] or [Shift] [-] keys. If you press and hold [+], [-], or [Shift] [-], the values scroll rapidly. To save the value, press [Select] or [Enter]. Press [Item] to continue. (NOTE: the 5Si Series do not have [-] or [Shift] [-] keys.) 9. Configure the remaining bytes of the IP address in the same manner. Note that a valid IP address is required for proper operation of the card. You can configure the subnet mask bytes (SM), syslog server IP address (LG), default gateway (GW), and timeout (TIMEOUT) in the same manner. The TIMEOUT parameter default is 90 seconds. Up to 3600 seconds can be configured. If set to "0", the timeout feature of the HP JetDirect card is disabled-TCP/IP connections will remain open until closed by the server. 10. To activate the printer and save your changes, press [On Line] (for LaserJet 5 Series printers, press [Go]). To configure the network operating system, see the HP JetDirect software installation guide included with the product. Using the Control Panel for Printers 3-11 Printer Control 3 Panel

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Using the Control Panel for Printers 3-11
3
Printer Control
Panel
6.
Change this to
CFG TCP/IP=YES*
by pressing
[+]
, and then
pressing
[Select]
or
[Enter]
depending on your printer model.
7.
Press
[Item]
until
BOOTP=YES*
or
BOOTP=NO*
appears.
•
The asterisk (
*
) indicates the active selection.
•
To change the BOOTP= setting, press
[+]
. Then press
[Select]
or
[Enter]
depending on your printer model. Be sure
“
*
”
appears alongside your selection.
If
BOOTP=YES*
, the printer is configured to retrieve its
TCP/IP parameters over the network using BOOTP or DHCP.
No other TCP/IP prompts will be displayed on the printer
’
s
control panel. To activate the printer and save your changes,
press
[OnLine]
or
[Go]
depending on your printer model.
If
BOOTP=NO *
, the printer is configured to accept TCP/IP
parameters from the printer
’
s control panel. Press
[Item]
to
configure each TCP/IP parameter.
IP BYTE 1=<value>*
should appear on the control panel first. Continue with step 8.
8.
To enter the first byte of the IP address, use the
[+]
,
[-]
or
[Shift] [-]
keys. If you press and hold
[+]
,
[-]
, or
[Shift] [-]
, the values
scroll rapidly. To save the value, press
[Select]
or
[Enter]
. Press
[Item]
to continue. (NOTE: the 5Si Series do not have
[-]
or
[Shift] [-]
keys.)
9.
Configure the remaining bytes of the IP address in the same
manner. Note that a valid IP address is required for proper
operation of the card.
You can configure the subnet mask bytes (SM), syslog server IP
address (LG), default gateway (GW), and timeout (TIMEOUT)
in the same manner.
The TIMEOUT parameter default is 90 seconds. Up to
3600 seconds can be configured. If set to
“
0
”
, the timeout
feature of the HP JetDirect card is disabled
—
TCP/IP
connections will remain open until closed by the server.
10.
To activate the printer and save your changes, press
[On°Line]
(for LaserJet 5 Series printers, press
[Go]
).
To configure the network operating system, see the HP JetDirect
software installation guide included with the product.