HP 400N HP JetDirect 400N Print Server Hardware Installation Guide - 5969-3587 - Page 57

Configuring TCP/IP Parameters - download

Get HP 400N - JetDirect MIO Print Server PDF manuals and user guides
UPC - 088698733714
View all HP 400N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Configuring TCP/IP Parameters Using the control panel of your printer, you can manually configure these TCP/IP parameters: • You can configure BOOTP, which automatically downloads configuration data over the network (this is the default setting), or • You can enter these parameters individually: • IP address (4 bytes) • Subnet mask (4 bytes) • Syslog server IP address (4 bytes) • Default gateway (4 bytes) • TCP connection timeout (in seconds) NOTE A valid IP address is required for proper operation of the card on a TCP/IP network. NOTE For DHCP (Dynamic Host Configuration Protocol) operation, BOOTP must be enabled. If an IP address is configured through DHCP and is subsequently changed through the control panel, the DHCP assigned address is released. If a printer is configured through DHCP, and you manually change the subnet mask or default gateway through the control panel, you should also change the IP address. Printer Control 3 Panel Using the Control Panel for Printers 3-9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Using the Control Panel for Printers 3-9
3
Printer Control
Panel
Configuring TCP/IP Parameters
Using the control panel of your printer, you can manually configure
these TCP/IP parameters:
•
You can configure BOOTP, which automatically downloads
configuration data over the network (this is the default setting),
or
•
You can enter these parameters individually:
•
IP address (4 bytes)
•
Subnet mask (4 bytes)
•
Syslog server IP address (4 bytes)
•
Default gateway (4 bytes)
•
TCP connection timeout (in seconds)
NOTE
A valid IP address is required for proper operation
of the card on a TCP/IP network.
NOTE
For DHCP (Dynamic Host Configuration Protocol)
operation, BOOTP must be enabled.
If an IP address is configured through DHCP and is
subsequently changed through the control panel,
the DHCP assigned address is released.
If a printer is configured through DHCP, and you
manually change the subnet mask or default
gateway through the control panel, you should
also change the IP address.