HP 400N HP JetDirect 400N Print Server Hardware Installation Guide - 5969-3587 - Page 79

MIO SETUP, IP BYTE 1=<value&gt, TIMEOUT, Ready to plot, CFG TCP/IP=NO, BOOTP, BOOTP=YES

Get HP 400N - JetDirect MIO Print Server PDF manuals and user guides
UPC - 088698733714
View all HP 400N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

5. Press ↑ to configure each TCP/IP parameter. For the first parameter, MIO SETUP and IP BYTE 1=→ appear. 6. To maintain the current value, press ↑. 7. To change the value, proceed as follows: a. Press [Enter] to display the current value. b. Press ↑ until the value that you want appears. c. Press [Enter] to save the new value. MIO SETUP and IP BYTE 1=→ appear. d. Press ↑ to continue. 8. Configure the remaining bytes of the IP address in the same manner. Note that a valid IP address is required for proper operation. 9. If you want, configure the subnet mask bytes (SM), syslog server IP address (LG), default gateway (GW), and timeout (TIMEOUT) in the same manner. The TIMEOUT parameter default is 90 seconds. Up to 3600 seconds can be configured. If set to "0", the timeout feature of the HP JetDirect card is disabled-TCP/IP connections remain open until closed by the server. 10. Press [Previous] until Ready to plot is displayed. For the 700/2000/2500/3000/3500 Series Printers 1. Access the configuration menu (see "To enable or disable network protocols" in this chapter). 2. From the CFG TCP/IP=NO→ menu item, press [Enter], ↓, [Enter] to display CFG TCP/IP=YES→ . 3. Press ↑ to display "BOOTP=". a. To maintain the current "BOOTP=" setting, press ↑ . b. To change the "BOOTP=" setting, press [Enter], ↑ , [Enter]. • If you select BOOTP=YES→ , the printer is configured to retrieve its TCP/IP parameters over the network using BOOTP or DHCP. No other TCP/IP prompts are displayed on the printer's control panel. Press ↑ to continue with configuration of other network protocols, or press [Previous] until the STATUS Ready is displayed. Control Panel for Large-Format Printers 4-11 HP DesignJet 4 Control Panel

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Control Panel for Large-Format Printers 4-11
4
HP DesignJet
Control Panel
5.
Press
↑
to configure each TCP/IP parameter. For the first
parameter,
MIO SETUP
and
IP BYTE 1=<value>
→
appear.
6.
To maintain the current value, press
↑
.
7.
To change the value, proceed as follows:
a. Press
[Enter]
to display the current value.
b. Press
↑
until the value that you want appears.
c. Press
[Enter]
to save the new value.
MIO SETUP
and
IP BYTE 1=<new value>
→
appear.
d. Press
↑
to continue.
8.
Configure the remaining bytes of the IP address in the same
manner. Note that a valid IP address is required for proper
operation.
9.
If you want, configure the subnet mask bytes (
SM
), syslog server
IP address (
LG
), default gateway (
GW
), and timeout (
TIMEOUT
)
in the same manner.
The
TIMEOUT
parameter default is 90 seconds. Up to
3600 seconds can be configured. If set to
“
0
”
, the timeout
feature of the HP JetDirect card is disabled
—
TCP/IP
connections remain open until closed by the server.
10. Press
[Previous]
until
Ready to plot
is displayed.
For the 700/2000/2500/3000/3500 Series Printers
1.
Access the configuration menu (see
“
To enable or disable
network protocols
”
in this chapter).
2.
From the
CFG TCP/IP=NO
→
menu item, press
[Enter]
,
↓
,
[Enter]
to display
CFG TCP/IP=YES
→
.
3.
Press
↑
to display
“
BOOTP=
”
.
a. To maintain the current
“
BOOTP=
”
setting, press
↑
.
b. To change the
“
BOOTP=
”
setting, press
[Enter]
,
↑
,
[Enter]
.
•
If you select
BOOTP=YES
→ ,
the printer is configured to
retrieve its TCP/IP parameters over the network using
BOOTP or DHCP.
No other TCP/IP prompts are displayed on the printer's
control panel. Press
↑
to continue with configuration of
other network protocols, or press
[Previous]
until the
STATUS Ready
is displayed.