HP 400N HP JetDirect 400N Print Server Hardware Installation Guide - 5969-3587 - Page 66

CFG TCP/IP YES, BOOTP YES, BOOTP NO, Value], Select], Item]

Get HP 400N - JetDirect MIO Print Server PDF manuals and user guides
UPC - 088698733714
View all HP 400N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

7. Change this to CFG TCP/IP YES by pressing [Value]. Then press [Select]. 8. Press [Item] until BOOTP YES or BOOTP NO appears. 9. To change the BOOTP setting, press [Value]. Then press [Select]. • If BOOTP YES is set, the printer is configured to retrieve its TCP/IP parameters over the network using BOOTP or DHCP. No other TCP/IP prompts will be displayed on the printer's control panel. • If BOOTP NO is set, the printer is configured to accept TCP/ IP parameters from the printer's control panel. Press [Item] to scroll through each TCP/IP parameter. Press [Value and [Select] to assign the value of each parameter. Note that a valid IP address is required for proper operation of the card. When assigning an IP address, you must enter the value of each byte. You can configure the subnet mask bytes (SM), syslog server IP address (LG), default gateway (GW), and timeout (TIMEOUT) in the same manner. The TIMEOUT parameter default is 90 seconds. Up to 3600 seconds can be configured. If set to "0", the timeout feature of the HP JetDirect card is disabled-TCP/IP connections will remain open until closed by the server. 10. To activate the printer and save your changes, press the online/ offline button . To configure the network operating system, see the HP JetDirect software installation guide included with the product. 3-18 Using the Control Panel for Printers

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
3-18
Using the Control Panel for Printers
7.
Change this to
CFG TCP/IP YES
by pressing
[Value]
. Then
press
[Select]
.
8.
Press
[Item]
until
BOOTP YES
or
BOOTP NO
appears.
9.
To change the BOOTP setting, press
[Value]
. Then press
[Select]
.
•
If
BOOTP YES
is set, the printer is configured to retrieve its
TCP/IP parameters over the network using BOOTP or DHCP.
No other TCP/IP prompts will be displayed on the printer
’
s
control panel.
•
If
BOOTP NO
is set, the printer is configured to accept TCP/
IP parameters from the printer
’
s control panel. Press
[Item]
to scroll through each TCP/IP parameter. Press
[Value°
and
[Select]
to assign the value of each parameter.
Note that a valid IP address is required for proper operation
of the card. When assigning an IP address, you must enter
the value of each byte.
You can configure the subnet mask bytes (SM), syslog server
IP address (LG), default gateway (GW), and timeout
(TIMEOUT) in the same manner.
The TIMEOUT parameter default is 90 seconds. Up to
3600 seconds can be configured. If set to
“
0
”
, the timeout
feature of the HP JetDirect card is disabled
—
TCP/IP
connections will remain open until closed by the server.
10.
To activate the printer and save your changes, press the online/
offline button
.
To configure the network operating system, see the HP JetDirect
software installation guide included with the product.