HP 400N HP JetDirect 400N Print Server Hardware Installation Guide - 5969-3587 - Page 91

HP J4100A 10/100Base-TX Print Server, Supported Links, Link-Speed LEDs

Get HP 400N - JetDirect MIO Print Server PDF manuals and user guides
UPC - 088698733714
View all HP 400N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

J4100A B 10/100Base-TX B HP J4100A 10/100Base-TX Print Server Supported Links HP J4100A JetDirect 10/100 Base-TX print servers support 10 or 100 Mbps operation in full- or half-duplex modes. In most cases, full-duplex is supported when the connecting network device- such as a network switch or hub-supports IEEE 802.3u autonegotiation specifications. When connecting to network devices that do not support auto-negotiation, or that implement non-conforming link negotiation, the print server will configure itself for 10- or 100-Mbps half-duplex operation. For example, when connected to a non-negotiating 10-Mbps hub, the print server card will be automatically set to operate at 10-Mbps half-duplex. If the card is not able to connect to the network through autonegotiation, you can manually set the link operating mode using link configuration jumpers on the card. Link-Speed LEDs The HP J4100A print server provides 2 light-emitting diodes (LEDs) near the RJ-45 connector. These LEDs indicate the operating link speed of the print server, either 10 or 100 Mbps. 10 Mbps LED 100 Mbps LED LED State: Description: Off Not linked On Link established at the indicated speed (Mbps) HP J4100A 10/100Base-TX Print Server B-1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
HP J4100A 10/100Base-TX Print Server B-1
B
J4100A
10/100Base-TX
B
HP J4100A 10/100Base-TX Print Server
Supported Links
HP J4100A JetDirect 10/100 Base-TX print servers support 10 or
100 Mbps operation in full- or half-duplex modes. In most cases,
full-duplex is supported when the connecting network device
—
such as a network switch or hub
—
supports IEEE 802.3u
autonegotiation specifications.
When connecting to network devices that do not support
auto-negotiation, or that implement non-conforming link
negotiation, the print server will configure itself for
10-
or
100-Mbps half-duplex
operation. For example, when connected
to a non-negotiating 10-Mbps hub, the print server card will
be automatically set to operate at
10-Mbps half-duplex
.
If the card is not able to connect to the network through
autonegotiation, you can manually set the link operating
mode using
link configuration jumpers
on the card.
Link-Speed LEDs
The HP J4100A print server provides 2 light-emitting diodes
(LEDs) near the RJ-45 connector. These LEDs indicate the
operating link speed of the print server, either 10 or 100 Mbps.
LED State:
Off
On
Description:
Not linked
Link established at the
indicated speed (Mbps)
100 Mbps LED
10 Mbps LED