HP 6125XLG R2306-HP 6125XLG Blade Switch IRF Configuration Guide - Page 38
Configuration procedure, Connect Device B to Device A as shown
View all HP 6125XLG manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 38 highlights
Configuration procedure 1. Configure Device A: # Shut down the physical ports used for IRF connection. This example uses the SFP+ port group that contains Ten-GigabitEthernet 1/1/7, Ten-GigabitEthernet 1/1/8, Ten-GigabitEthernet 1/1/11, and Ten-GigabitEthernet 1/1/12 for IRF connection. system-view [Sysname] interface range name irf interface ten-gigabitethernet 1/1/7 ten-gigabitethernet 1/1/8 ten-gigabitethernet 1/1/11 ten-gigabitethernet 1/1/12 [Sysname-if-range-irf] shutdown [Sysname-if-range-irf] quit # Bind Ten-GigabitEthernet 1/1/7 and Ten-GigabitEthernet 1/1/8 to IRF-port 1/1. [Sysname] irf-port 1/1 [Sysname-irf-port1/1] port group interface ten-gigabitethernet 1/1/7 [Sysname-irf-port1/1] port group interface ten-gigabitethernet 1/1/8 [Sysname-irf-port1/1] quit # Bind Ten-GigabitEthernet 1/1/11 and Ten-GigabitEthernet 1/1/12 to IRF-port 1/2. [Sysname] irf-port 1/2 [Sysname-irf-port1/2] port group interface ten-gigabitethernet 1/1/11 [Sysname-irf-port1/2] port group interface ten-gigabitethernet 1/1/12 [Sysname-irf-port1/2] quit # Bring up the SFP+ ports and save the configuration. [Sysname] interface range name irf [Sysname-if-range-irf] undo shutdown [Sysname-if-range-irf] quit [Sysname] save # Activate the IRF port configuration. [Sysname] irf-port-configuration active 2. Configure Device B: # Change the member ID of Device B to 2, and reboot the device to validate the change. system-view [Sysname] irf member 1 renumber 2 Renumbering the member ID may result in configuration change or loss. Continue? [Y/N]:y [Sysname] quit reboot # Connect Device B to Device A as shown in Figure 14, and log in to Device B. This example uses the SFP+ group that contains Ten-GigabitEthernet 2/1/7, Ten-GigabitEthernet 2/1/8, Ten-GigabitEthernet 2/1/11, and Ten-GigabitEthernet 2/1/12 for IRF connection. # Shut down the physical ports. system-view [Sysname] interface range name irf interface ten-gigabitethernet 2/1/7 ten-gigabitethernet 2/1/8 ten-gigabitethernet 2/1/11 ten-gigabitethernet 2/1/12 [Sysname-if-range-irf] shutdown [Sysname-if-range-irf] quit # Bind Ten-GigabitEthernet 2/1/7 and Ten-GigabitEthernet 2/1/8 to IRF-port 2/1. [Sysname] irf-port 2/1 [Sysname-irf-port2/1] port group interface ten-gigabitethernet 2/1/7 34