HP 6125XLG R2306-HP 6125XLG Blade Switch IRF Configuration Guide - Page 40

Connect Device D to Device B and Device C as shown in, Con LACP MAD on the IRF fabric

Get HP 6125XLG PDF manuals and user guides View all HP 6125XLG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

[Sysname] save # Activate the IRF port configuration. [Sysname] irf-port-configuration active Device C reboots to join the IRF fabric. 4. Configure Device D: # Change the member ID of Device D to 4, and reboot the device to validate the change. system-view [Sysname] irf member 1 renumber 4 Renumbering the member ID may result in configuration change or loss. Continue? [Y/N]:y [Sysname] quit reboot # Connect Device D to Device B and Device C as shown in Figure 14, and log in to Device D. This example uses the SFP+ port group that contains Ten-GigabitEthernet 4/1/7, Ten-GigabitEthernet 4/1/8, Ten-GigabitEthernet 4/1/11, and Ten-GigabitEthernet 4/1/12 for IRF connection. # Shut down the physical ports. system-view [Sysname] interface range name irf interface ten-gigabitethernet 4/1/7 ten-gigabitethernet 4/1/8 ten-gigabitethernet 4/1/11 ten-gigabitethernet 4/1/12 [Sysname-if-range-irf] shutdown [Sysname-if-range-irf] quit # Bind Ten-GigabitEthernet 4/1/7 and Ten-GigabitEthernet 4/1/8 to IRF-port 4/1. [Sysname] irf-port 4/1 [Sysname-irf-port4/1] port group interface ten-gigabitethernet 4/1/7 [Sysname-irf-port4/1] port group interface ten-gigabitethernet 4/1/8 [Sysname-irf-port4/1] quit # Bind Ten-GigabitEthernet 4/1/11 and Ten-GigabitEthernet 4/1/12 to IRF-port 4/2. [Sysname] irf-port 4/2 [Sysname-irf-port4/2] port group interface ten-gigabitethernet 4/1/11 [Sysname-irf-port4/2] port group interface ten-gigabitethernet 4/1/12 [Sysname-irf-port4/2] quit # Bring up the SFP+ ports and save the configuration. [Sysname] interface range name irf [Sysname-if-range-irf] undo shutdown [Sysname-if-range-irf] quit [Sysname] save # Activate the IRF port configuration. [Sysname] irf-port-configuration active Device D reboots to join the IRF fabric. A four-chassis IRF fabric is formed. 5. Configure LACP MAD on the IRF fabric: # Set the domain ID of the IRF fabric to 1. system-view [Sysname] irf domain 1 # Create a dynamic aggregate interface and enable LACP MAD. [Sysname] interface bridge-aggregation 2 [Sysname-Bridge-Aggregation2] link-aggregation mode dynamic [Sysname-Bridge-Aggregation2] mad enable 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
36
[Sysname] save
# Activate the IRF port configuration.
[Sysname] irf-port-configuration active
Device C reboots to join the IRF fabric.
4.
Configure Device D:
# Change the member ID of Device D to 4, and reboot the device to validate the change.
<Sysname> system-view
[Sysname] irf member 1 renumber 4
Renumbering the member ID may result in configuration change or loss. Continue? [Y/N]:y
[Sysname] quit
<Sysname> reboot
# Connect Device D to Device B and Device C as shown in
Figure 14
, and log in to Device D. This
example uses the SFP+ port group that contains Ten-GigabitEthernet 4/1/7, Ten-GigabitEthernet
4/1/8, Ten-GigabitEthernet 4/1/11, and Ten-GigabitEthernet 4/1/12 for IRF connection.
# Shut down the physical ports.
<Sysname> system-view
[Sysname] interface range name irf interface ten-gigabitethernet 4/1/7
ten-gigabitethernet 4/1/8 ten-gigabitethernet 4/1/11 ten-gigabitethernet 4/1/12
[Sysname-if-range-irf] shutdown
[Sysname-if-range-irf] quit
# Bind Ten-GigabitEthernet 4/1/7 and Ten-GigabitEthernet 4/1/8 to IRF-port 4/1.
[Sysname] irf-port 4/1
[Sysname-irf-port4/1] port group interface ten-gigabitethernet 4/1/7
[Sysname-irf-port4/1] port group interface ten-gigabitethernet 4/1/8
[Sysname-irf-port4/1] quit
# Bind Ten-GigabitEthernet 4/1/11 and Ten-GigabitEthernet 4/1/12 to IRF-port 4/2.
[Sysname] irf-port 4/2
[Sysname-irf-port4/2] port group interface ten-gigabitethernet 4/1/11
[Sysname-irf-port4/2] port group interface ten-gigabitethernet 4/1/12
[Sysname-irf-port4/2] quit
# Bring up the SFP+ ports and save the configuration.
[Sysname] interface range name irf
[Sysname-if-range-irf] undo shutdown
[Sysname-if-range-irf] quit
[Sysname] save
# Activate the IRF port configuration.
[Sysname] irf-port-configuration active
Device D reboots to join the IRF fabric. A four-chassis IRF fabric is formed.
5.
Configure LACP MAD on the IRF fabric:
# Set the domain ID of the IRF fabric to 1.
<Sysname> system-view
[Sysname] irf domain 1
# Create a dynamic aggregate interface and enable LACP MAD.
[Sysname] interface bridge-aggregation 2
[Sysname-Bridge-Aggregation2] link-aggregation mode dynamic
[Sysname-Bridge-Aggregation2] mad enable