HP 6125XLG R2306-HP 6125XLG Blade Switch High Availability Command Reference - Page 60

dldp authentication-mode

Get HP 6125XLG PDF manuals and user guides View all HP 6125XLG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Related commands reset dldp statistics dldp authentication-mode Use dldp authentication-mode to configure DLDP authentication. Use undo dldp authentication-mode to restore the default. Syntax dldp authentication-mode { md5 | none | simple } undo dldp authentication-mode Default DLDP authentication is not performed. Views System view Predefined user roles network-admin Parameters md5: Specifies the MD5 authentication mode. none: Specifies not to perform authentication. simple: Specifies the plain text authentication mode. Usage guidelines To enable DLDP to operate properly, make sure the DLDP authentication modes and the passwords configured on the two ends of a link are the same. If you do not configure the authentication password after you configure the authentication mode, the authentication mode is none no matter which authentication mode you configure. Examples # Configure to perform plain text authentication and set the password to abc (assuming that Device A and Device B are connected by a DLDP link). • Configure Device A: system-view [DeviceA] dldp authentication-mode simple [DeviceA] dldp authentication-password simple abc • Configure Device B: system-view [DeviceB] dldp authentication-mode simple [DeviceB] dldp authentication-password simple abc Related commands • display dldp • dldp authentication-password 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
55
Related commands
reset dldp statistics
dldp authentication-mode
Use
dldp authentication-mode
to configure DLDP authentication.
Use
undo dldp authentication-mode
to restore the default.
Syntax
dldp authentication-mode
{
md5
|
none
|
simple
}
undo dldp authentication-mode
Default
DLDP authentication is not performed.
Views
System view
Predefined user roles
network-admin
Parameters
md5
: Specifies the MD5 authentication mode.
none
: Specifies not to perform authentication.
simple
: Specifies the plain text authentication mode.
Usage guidelines
To enable DLDP to operate properly, make sure the DLDP authentication modes and the passwords
configured on the two ends of a link are the same.
If you do not configure the authentication password after you configure the authentication mode, the
authentication mode is
none
no matter which authentication mode you configure.
Examples
# Configure to perform plain text authentication and set the password to
abc
(assuming that Device A
and Device B are connected by a DLDP link).
•
Configure Device A:
<DeviceA> system-view
[DeviceA] dldp authentication-mode simple
[DeviceA] dldp authentication-password simple abc
•
Configure Device B:
<DeviceB> system-view
[DeviceB] dldp authentication-mode simple
[DeviceB] dldp authentication-password simple abc
Related commands
•
display dldp
•
dldp authentication-password