HP C3982A User Manual - Page 19

Attaching a Parallel Printer Cable

Get HP C3982A - LaserJet 6mp B/W Laser Printer PDF manuals and user guides View all HP C3982A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Attaching a Parallel Printer Cable To ensure reliability use an IEEE-1284 compliant parallel cable (these cables are clearly marked with "IEEE-1284"). Only IEEE-1284 cables support all of the printer's advanced functions. Caution Make sure power is off. 1 Locate the interface cable door (A) at the back of the printer. Pull the door out using the finger tab for leverage. 2 If using a parallel cable with a large B-type end, connect the cable into port (B). Snap the wire clips in place to secure the cable to the printer. If using a parallel cable with a small C-type end, connect the cable into port (C). The cables should install easily. If installation is difficult, check the cable orientation. 3 Replace the interface cable door while allowing the cable to feed through its appropriate hole. 4 Connect the other end of the cable to the proper connector on the computer. Go to Step 7. Attach the Power Cord, on page 1-12. 1-10 Printer Setup EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
Attaching a Parallel Printer Cable
To ensure reliability use an IEEE-1284
compliant parallel cable (these cables are
clearly marked with “IEEE-1284”). Only
IEEE-1284 cables support all of the
printer’s advanced functions.
Caution
Make sure power is off.
1
Locate the interface cable door (
A
) at
the back of the printer. Pull the door
out using the finger tab for leverage.
2
If using a parallel cable with a large
B-type end, connect the cable into
port (
B
). Snap the wire clips in place
to secure the cable to the printer.
If using a parallel cable with a small
C-type end, connect the cable into
port (
C
).
The cables should install easily. If
installation is difficult, check the
cable orientation.
3
Replace the interface cable door
while allowing the cable to feed
through its appropriate hole.
4
Connect the other end of the cable to
the proper connector on the computer.
Go to
Step 7. Attach the Power Cord
,
on page 1-12.
1-10
Printer Setup
EN