HP LH4r HP Netserver LP 2000r (1.13, 1.26 & 1.40 GHz) User Guide - Page 119

Replacing a Battery, Opening and Closing the HP Netserver.

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 119 highlights

Chapter 12 Troubleshooting Replacing a Battery If your HP Netserver repeatedly loses its configuration or the processor clock stops, you should replace the battery. WARNING There is danger of explosion if the battery is incorrectly installed. For your safety, never attempt to recharge, disassemble, or burn the old battery. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. 1. Power down the HP Netserver and unplug power cord. 2. Extend the Netserver out from the rack. 3. Remove the Netserver cover and the air flow guide. Refer to Chapter 2, "Opening and Closing the HP Netserver." 4. Remove the PCI card cage. Refer to Chapter 2. 5. Insert a small flatblade screwdriver or similar tool between the battery and spring latch. See Figure 12-3. 6. Push the spring latch away from battery to release the battery and then remove the battery. 113

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
Chapter 12
Troubleshooting
113
Replacing a Battery
If your HP Netserver repeatedly loses its configuration or the processor clock
stops, you should replace the battery.
WARNING
There is danger of explosion if the battery is incorrectly
installed. For your safety, never attempt to recharge,
disassemble, or burn the old battery. Replace only with the
same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's
instructions.
1. Power down the HP Netserver and unplug power cord.
2. Extend the Netserver out from the rack.
3. Remove the Netserver cover and the air flow guide. Refer to
Chapter 2, "Opening and Closing the HP Netserver."
4. Remove the PCI card cage. Refer to Chapter 2.
5. Insert a small flatblade screwdriver or similar tool between the battery and
spring latch. See Figure 12-3.
6. Push the spring latch away from battery to release the battery and then remove
the battery.