HP LH4r HP Netserver LP 2000r (1.13, 1.26 & 1.40 GHz) User Guide - Page 31

See Opening Drive Ejector Arms

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Chapter 3 Installing Mass Storage Devices Figure 3-5. Opening Drive Ejector Arms 2. Remove the drive: a. Using both hands, grasp the ejector arms and firmly pull the drive out about an inch to disengage the connection on the backplane. See Figure 3-6. b. Wait about 30 seconds for the drive to stop spinning and for the drive heads to park. c. Use your hand to support the bottom of the drive, while you slowly pull the drive straight out. Do not allow the drive to fall. 3. Place the drive in an electrostatic protected container. Do not stack drives. 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
Chapter 3
Installing Mass Storage Devices
25
Figure 3-5. Opening Drive Ejector Arms
2. Remove the drive:
a.
Using both hands, grasp the ejector arms and firmly pull the drive out
about an inch to disengage the connection on the backplane.
See Figure 3-6.
b. Wait about 30 seconds for the drive to stop spinning and for the drive
heads to park.
c.
Use your hand to support the bottom of the drive, while you slowly pull
the drive straight out.
Do not allow the drive to fall.
3. Place the drive in an electrostatic protected container.
Do not stack drives.