HP LH4r HP Netserver LP 2000r (1.13, 1.26 & 1.40 GHz) User Guide - Page 72

Installing Slides in the Rack, See

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

Chapter 7 Rack Mounting the HP Netserver (4-Post) Installing Slides in the Rack 1. Ensure the rack is stabilized. For HP system /E or /U racks, pull the anti-tip foot forward out of the bottom of the rack and lower the leveler screws to make firm contact with the floor. See Figure 7-3. Leveler Screws (4) Anti-tip Foot Extended Figure 7-3. Installing Slides in the Rack 2. Insert the rear slide mounting pins into holes you have marked on the rear column. Then push in on the front of the slide and snap the front mounting pins into holes marked on the front column. The slide mounting pins insert into the inside face of the rear column and the front face of the front column. See Figure 7-3. 66

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
Chapter 7
Rack Mounting the HP Netserver (4-Post)
66
Installing Slides in the Rack
1. Ensure the rack is stabilized.
For HP system /E or /U racks, pull the anti-tip foot forward out of the bottom
of the rack and lower the leveler screws to make firm contact with the floor.
See Figure 7-3.
Anti-tip Foot
Extended
Leveler
Screws (4)
Figure 7-3. Installing Slides in the Rack
2. Insert the rear slide mounting pins into holes you have marked on the rear
column. Then push in on the front of the slide and snap the front mounting
pins into holes marked on the front column.
The slide mounting pins insert into the
inside
face of the rear column and the
front
face of the front column. See Figure 7-3.