HP LH4r HP Netserver LP 2000r (1.13, 1.26 & 1.40 GHz) User Guide - Page 42

Removing DIMMs, Refer to Removing the Top Cover in Opening and Closing

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Chapter 4 Installing Additional Memory 0 1 DIMM Slots 2 3 System Board Figure 4-4. Inserting DIMMs Removing DIMMs You may need to remove a DIMM module to downsize your memory configuration or to replace a defective DIMM. 1. Log off all users, back up files, and power down the HP Netserver. For detailed instructions, see "Powering-Down the HP Netserver," in Chapter 1, "Controls, Ports and Indicators." 2. Pull out the anti-tip foot at the bottom of the rack. Then slowly slide the HP Netserver chassis out from the rack as far as it can be extended. It is not necessary to remove the HP Net Server from the rack to install DIMMs. 3. Disconnect the power cables and all external cables. If necessary, label each one to support re-assembly. WARNING The power supply will continue to provide standby current to the HP Netserver until the power cable is disconnected. 4. Remove the top cover. Refer to "Removing the Top Cover" in Chapter 2, "Opening and Closing the HP Netserver." 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
Chapter 4
Installing Additional Memory
36
0
1
2
3
DIMM
Slots
System Board
Figure 4-4. Inserting DIMMs
Removing DIMMs
You may need to remove a DIMM module to downsize your memory
configuration or to replace a defective DIMM.
1. Log off all users, back up files, and power down the HP Netserver.
For detailed instructions, see "Powering-Down the HP Netserver," in
Chapter 1, "Controls, Ports and Indicators."
2. Pull out the anti-tip foot at the bottom of the rack. Then slowly slide the HP
Netserver chassis out from the rack as far as it can be extended.
It is not necessary to remove the HP Net Server from the rack to install
DIMMs.
3. Disconnect the power cables and all external cables.
If necessary, label each one to support re-assembly.
WARNING
The power supply will continue to provide standby current to
the HP Netserver until the power cable is disconnected.
4. Remove the top cover.
Refer to "Removing the Top Cover" in Chapter 2, "Opening and Closing the
HP Netserver."