HP LH4r HP Netserver LP 2000r (1.13, 1.26 & 1.40 GHz) User Guide - Page 17

Replacing the Top Cover, See

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Chapter 2 Opening and Closing the HP Netserver 4. Release the top cover by turning the knob at the front of the chassis in a clockwise direction. See Figure 2-2. 5. Slide the top cover about ½ inch (13mm) toward the front of the Netserver and then lift it off the chassis. Figure 2-2. Removing the Top Cover Replacing the Top Cover To replace the cover, follow these steps. 1. Ensure the knob on the cover is turned to the Open position (clockwise). See Figure 2-3. 2. Place the rear edge of the top cover near the rear edge of the chassis, angling the cover slightly to engage the hooks at the rear of the chassis. Then lay the cover down on the chassis. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
Chapter 2
Opening and Closing the HP Netserver
11
4. Release the top cover by turning the knob at the front of the chassis in a
clockwise direction. See Figure 2-2.
5. Slide the top cover about ½ inch (13mm) toward the front of the Netserver
and then lift it off the chassis.
Figure 2-2. Removing the Top Cover
Replacing the Top Cover
To replace the cover, follow these steps.
1. Ensure the knob on the cover is turned to the Open position (clockwise).
See Figure 2-3.
2. Place the rear edge of the top cover near the rear edge of the chassis, angling
the cover slightly to engage the hooks at the rear of the chassis. Then lay the
cover down on the chassis.