HP LH4r HP Netserver LP 2000r (1.13, 1.26 & 1.40 GHz) User Guide - Page 91

Attaching the Front Bezel, Cabling Rack Components

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

Chapter 8 Rack Mounting the HP Netserver (2-Post) Attaching the Front Bezel The bezel attaches to the brackets on the front of the HP Netserver. 1. Hook the bottom edge of the bezel onto the pins on the brackets. See Figure 8-8 (figure shows flush-mount brackets). 2. Close the bezel and press the top corners to snap it into place. Pin A Pin B Figure 8-8. Attaching the Front Bezel Cabling Rack Components After installing the HP Netserver in the rack, refer to the white paper entitled HP Netserver High Density Rack Solutions Overview (LP 1000r and LP 2000r) to cable the Netserver in the rack enclosure. The white paper is available on HP's web site at the following URL: http://www.hp.com/netserver/support 85

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
Chapter 8
Rack Mounting the HP Netserver (2-Post)
85
Attaching the Front Bezel
The bezel attaches to the brackets on the front of the HP Netserver.
1. Hook the bottom edge of the bezel onto the pins on the brackets.
See Figure 8-8 (figure shows flush-mount brackets).
2. Close the bezel and press the top corners to snap it into place.
Pin
Pin
B
A
Figure 8-8. Attaching the Front Bezel
Cabling Rack Components
After installing the HP Netserver in the rack, refer to the white paper entitled
HP Netserver High Density Rack Solutions Overview (LP 1000r and LP 2000r)
to cable the Netserver in the rack enclosure. The white paper is available on HP's
web site at the following URL: