HP LH4r HP Netserver LP 2000r (1.13, 1.26 & 1.40 GHz) User Guide - Page 43

Refer to Removing the Rear Chassis Blower/Bracket and Air Flow Guide,

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Chapter 4 Installing Additional Memory 5. Remove the air flow guide. See Figure 4-1. Refer to "Removing the Rear Chassis Blower/Bracket and Air Flow Guide" in Chapter 2, "Opening and Closing the HP Netserver." 6. Locate the DIMM slots on the system board. See Figure 4-2. 7. Open the retaining latches. 8. Lift the DIMM completely away from the slot. 9. Place the DIMM in its anti-static container. 10. Repeat Steps 6-9 for as many DIMMs as you need to remove. NOTE If you power up the HP Netserver when there are no DIMMs installed, the screen displays an error message or appears blank and sounds beep codes. 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
Chapter 4
Installing Additional Memory
37
5. Remove the air flow guide. See Figure 4-1.
Refer to "Removing the Rear Chassis Blower/Bracket and Air Flow Guide"
in Chapter 2, "Opening and Closing the HP Netserver."
6. Locate the DIMM slots on the system board. See Figure 4-2.
7. Open the retaining latches.
8. Lift the DIMM completely away from the slot.
9. Place the DIMM in its anti-static container.
10. Repeat Steps 6-9 for as many DIMMs as you need to remove.
NOTE
If you power up the HP Netserver when there are no DIMMs
installed, the screen displays an error message or appears blank
and sounds beep codes.