HP LH4r HP Netserver LP 2000r (1.13, 1.26 & 1.40 GHz) User Guide - Page 16

Replacing the Front Bezel, Removing the Top Cover, See

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Chapter 2 Opening and Closing the HP Netserver Figure 2-1. Removing the Front Bezel Replacing the Front Bezel 1. Hook the bottom edge of the bezel onto the pins at the front of the chassis. See Figure 2-1. 2. Close the bezel and press the top corners to snap it into place. Removing the Top Cover You do not need to remove the front bezel to remove the top cover of the Netserver. 1. If the HP Netserver is operating, log off all users and shut down the operating system. 2. Pull out the anti-tip foot at the bottom of the rack. Then slowly slide the HP Netserver chassis out from the rack. 3. Disconnect the power cord and unplug cables. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
Chapter 2
Opening and Closing the HP Netserver
10
Figure 2-1. Removing the Front Bezel
Replacing the Front Bezel
1. Hook the bottom edge of the bezel onto the pins at the front of the chassis.
See Figure 2-1.
2. Close the bezel and press the top corners to snap it into place.
Removing the Top Cover
You do not need to remove the front bezel to remove the top cover of the
Netserver.
1. If the HP Netserver is operating, log off all users and shut down the operating
system.
2. Pull out the anti-tip foot at the bottom of the rack. Then slowly slide the HP
Netserver chassis out from the rack.
3. Disconnect the power cord and unplug cables.