HP LH4r HP Netserver LP 2000r (1.13, 1.26 & 1.40 GHz) User Guide - Page 41

Aligning the DIMM, It is important to hold the DIMM firmly with both hands and use even

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Chapter 4 Installing Additional Memory 9. Align the notches on the DIMM with the keys on the slot. See Figure 4-3. DIMM Slot Keys Retaining Latches (2) Notches 30 Degrees Figure 4-3. Aligning the DIMM 10. Hold the DIMM at approximately 30 ° to the system board and press the DIMM firmly and evenly into the slot until the retaining latches close. See Figures 4-3 and 4-4. It is important to hold the DIMM firmly with both hands and use even pressure so as not to bend or break the DIMM connector during installation. If the latches do not close, the DIMM is not inserted correctly. 11. Repeat Steps 7-10 to install additional DIMMs for your memory configuration. 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
Chapter 4
Installing Additional Memory
35
9. Align the notches on the DIMM with the keys on the slot. See Figure 4-3.
DIMM
Slot
Keys
Retaining Latches (2)
Notches
30 Degrees
Figure 4-3. Aligning the DIMM
10. Hold the DIMM at approximately 30
°
to the system board and press the
DIMM
firmly and evenly
into the slot until the retaining latches close.
See Figures 4-3 and 4-4.
It is important to hold the DIMM firmly with both hands and use even
pressure so as not to bend or break the DIMM connector during installation.
If the latches do not close, the DIMM is not inserted correctly.
11. Repeat Steps 7-10 to install additional DIMMs for your memory
configuration.