HP LaserJet 4v/mv HP LaserJet 4V and 4MV Printer - User’s Guide, C314 - Page 62

Job Menu

Get HP LaserJet 4v/mv PDF manuals and user guides View all HP LaserJet 4v/mv manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Table 4-5 Job Menu You can change Job Menu items through your software application if you have installed an appropriate printer driver. Job Menu Items Item RESOLUTION PERSONALTY PWRSAVE IO TIMEOUT PAGEPROTCT *Factory default. Options Explanation 300 or 600* At 600 dpi (dots per inch), the printer might need as much as four times more memory to format a page than it needs at 300 dpi. For most purposes, 600 dpi is recommended. AUTO* PCL PS Personality means printer language. Your printer can switch from its standard personality, PCL, to other personalities, such as PostScript. When PERSONALTY is set to AUTO, the printer analyzes each print job it receives and switches personalities automatically. When you make another personality the default, the printer stops switching personalities automatically unless a software command specifically instructs it to do so. (See "Switching Printer Languages (Personalities)" in Chapter 5.) OFF, 15 MIN, 30 MIN*, 1 HR, 2 HRS, 3 HRS If you select PS as the default, you may want to set ADV FNCTNS in the Parallel Menu to OFF. Sets the amount of time the printer is idle before the fuser shuts down. The printer automatically starts warming the fuser when you send a print job to the printer, press a control panel key, load or remove paper, or open the top door. (See "Saving Energy with Power Save" in Chapter 5.) 5 to 300 15* I/O timeout refers to the time, measured in seconds, that the printer waits before ending an incomplete print job. Scrolls in increments of 10. This setting allows you to adjust timeout for best performance. If data from other ports appear in the middle of your print job, increase the timeout value. AUTO* ON You will not see this item unless the error 21 PRINT OVERRUN has occurred. (See Chapter 8, "Solving Printer Problems.") 4 Understanding the Control Panel 4-9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
Job Menu
You can change Job Menu items through your software application if you
have installed an appropriate printer driver.
Item
Options
Explanation
RESOLUTION
300 or 600*
At 600 dpi (dots per inch), the printer might need as much as
four times more memory to format a page than it needs at
300 dpi. For most purposes, 600 dpi is recommended.
PERSONALTY
AUTO*
PCL
PS
Personality
means printer language. Your printer can switch
from its standard personality, PCL, to other personalities,
such as PostScript. When
PERSONALTY
is set to
AUTO
, the
printer analyzes each print job it receives and switches
personalities automatically.
When you make another personality the default, the printer
stops switching personalities automatically unless a software
command specifically instructs it to do so. (See “Switching
Printer Languages (Personalities)” in Chapter 5.)
If you select PS as the default, you may want to set
ADV FNCTNS
in the Parallel Menu to
OFF
.
PWRSAVE
OFF, 15 MIN,
30 MIN*, 1 HR,
2 HRS, 3 HRS
Sets the amount of time the printer is idle before the fuser
shuts down. The printer automatically starts warming the
fuser when you send a print job to the printer, press a control
panel key, load or remove paper, or open the top door. (See
“Saving Energy with Power Save” in Chapter 5.)
IO TIMEOUT
5 to 300
15*
I/O timeout refers to the time, measured in seconds, that the
printer waits before ending an incomplete print job. Scrolls in
increments of 10. This setting allows you to adjust timeout for
best performance. If data from other ports appear in the
middle of your print job, increase the timeout value.
PAGEPROTCT
AUTO*
ON
You will not see this item unless the error
21 PRINT OVERRUN
has occurred. (See Chapter 8, “Solving Printer Problems.”)
*Factory default.
Table 4-5
Job Menu Items
4
Understanding the Control Panel 4-9