Home » HP Manuals » Desktops » HP Pro 3330 » Manual Viewer

HP Pro 3330 HP Pro 3330 Microtower PC, HP Pro 3330 Small Form Factor PC, and H - Page 187

Solving Memory Problems

Add to My Manuals
Save this manual to your list of manuals

Page 187 highlights

System setup utility reports unprogrammed EEPROM. Cause Unprogrammed EEPROM. Solution Contact an authorized service provider. Solving Memory Problems If you encounter memory problems, some common causes and solutions are listed in the following table. CAUTION: Power may still be supplied to the DIMMs when the computer is turned off (depending on the Management Engine (ME) settings). To avoid damage to the DIMMs or the system board, you must unplug the computer power cord before attempting to reseat, install, or remove a DIMM module. For those systems that support ECC memory, HP does not support mixing ECC and non-ECC memory. Otherwise, the computer will not boot the operating system. NOTE: The memory count will be affected by configurations with the Management Engine (ME) enabled. The ME uses 8MB of system memory in single channel mode or 16MB of memory in dualchannel mode to download, decompress, and execute the ME firmware for Out-of-Band (OOB), thirdparty data storage, and other management functions. Table D-13 Solving Memory Problems System will not boot or does not function properly after installing additional memory modules. Cause Solution A memory module is not installed in the DIMM1 or XMM1 socket. Ensure that a memory module is installed in the DIMM1 or XMM1 socket on the system board. This socket must be populated with a memory module. Memory module is not the correct type or speed grade for the system or the new memory module is not seated properly. Replace module with the correct industry-standard device for the computer. On some models, ECC and non-ECC memory modules cannot be mixed. Out of memory error. Cause Memory configuration may not be set up correctly. You have run out of memory to run the application. Solution Use the Device Manager to check memory configuration. Check the application documentation to determine the memory requirements. Memory count during POST is wrong. Cause The memory modules may not be installed correctly. Integrated graphics may use system memory. Solution Check that the memory modules have been installed correctly and that proper modules are used. No action required. Solving Memory Problems 177

Section	Page
Product Features	11
Identifying the Chassis	11
Serviceability Features	11
Feature Overview	12
Microtower Components	13
Small Form Factor Components	14
Installing and Customizing the Software	15
Installing the Operating System	15
Downloading Microsoft Windows Updates	15
Installing or Upgrading Device Drivers (Windows systems)	16
Accessing Disk Image (ISO) Files	16
Protecting the Software	16
Computer Setup (F10) Utility	17
Computer Setup (F10) Utilities	17
Using Computer Setup (F10) Utilities	18
Computer Setup—File	18
Computer Setup—Storage	20
Computer Setup—Security	22
Computer Setup—Power	25
Computer Setup—Advanced	26
Recovering the Configuration Settings	27
Illustrated parts catalog	28
Microtower (MT) Chassis Spare Parts	28
Computer Major Components	28
Cables	30
Misc Parts	31
Drives	32
Misc Boards	32
Sequential Part Number Listing	32
Small Form Factor (SFF) Chassis Spare Parts	35
Computer major components	35
Cables	37
Misc Parts	38
Drives	38
Misc Boards	39
Sequential Part Number Listing	39
Serial ATA (SATA) Drive Guidelines and Features	42
SATA Hard Drives	42
SATA Hard Drive Cables	42
SATA Data Cable	42
SMART ATA Drives	43
Hard Drive Capacities	43
Routine Care and Disassembly Preparation	44
Electrostatic Discharge Information	44
Generating Static	44
Preventing Electrostatic Damage to Equipment	45
Personal Grounding Methods and Equipment	46
Grounding the Work Area	46
Recommended Materials and Equipment	46
Operating Guidelines	47
Routine Care	48
General Cleaning Safety Precautions	48
Cleaning the Computer Case	48
Cleaning the Keyboard	48
Cleaning the Monitor	49
Cleaning the Mouse	49
Service Considerations	49
Power Supply Fan	49
Tools and Software Requirements	49
Screws	50
Cables and Connectors	50
Hard Drives	50
Lithium Coin Cell Battery	50
Removal and Replacement Procedures – Microtower (MT) Chassis	52
Preparation for Disassembly	52
Access Panel	53
Front Bezel	55
Memory	57
DDR3-SDRAM DIMMs	57
Populating DIMM Sockets	58
Removing Memory Modules	59
Expansion Cards	61
Cable Management	67
Cable Connections	68
Drives	69
Drive Positions	70
Installing Additional Drives	71
System Board Drive Connections	72
Removing an Optical Drive	73
Removing a Hard Drive	76
Front I/O and USB Panel Housing Assembly	83
Power Switch/LED Assembly	85
System Fan	87
Speaker	89
Fan Sink Assembly	90
Processor	92
Power Supply	95
System Board	97
Battery	98
Removal and Replacement Procedures – Small Form Factor (SFF) Chassis	100
Preparation for Disassembly	100
Access Panel	100
Front Bezel	102
Memory	103
DDR3-SDRAM DIMMs	103
Populating DIMM Sockets	104
Removing DIMMs	105
Expansion Card	108
Cable Management	112
Cable Connections	113
Drives	114
Drive Positions	114
Removing Drives	115
Removing an Optical Drive	115
Removing the Hard Drive	117
Power Switch	120
Front USB Assembly	122
Speaker	125
Fan Assembly	126
Fan Sink	129
Processor	131
Power Supply	133
System Board	136
Battery	137
Connector Pin Assignments	139
Ethernet BNC	139
USB	139
Microphone	139
Headphone	139
Line-in Audio	140
Line-out Audio	140
4-Pin Power (for CPU)	140
Monitor	141
Serial Interface, Powered and Non-Powered	141
DVI Connector	142
24-Pin Power	143
PCI Express	144
PCI Express	145
Power Cord Set Requirements	146
General Requirements	146
Japanese Power Cord Requirements	146
Country-Specific Requirements	147
POST Error Messages	148
POST Numeric Codes and Text Messages	148
Interpreting POST Diagnostic Front Panel LEDs and Audible Codes	156
Troubleshooting Without Diagnostics	160
Safety and Comfort	160
Before You Call for Technical Support	160
Helpful Hints	161
Solving General Problems	162
Solving Power Problems	165
Solving Diskette Problems	166
Solving Hard Drive Problems	169
Solving Media Card Reader Problems	172
Solving Display Problems	173
Solving Audio Problems	177
Solving Printer Problems	179
Solving Keyboard and Mouse Problems	180
Solving Hardware Installation Problems	181
Solving Network Problems	183
Solving Memory Problems	187
Solving Processor Problems	188
Solving CD-ROM and DVD Problems	189
Solving USB Flash Drive Problems	191
Solving Front Panel Component Problems	191
Solving Internet Access Problems	192
Solving Software Problems	195
Contacting Customer Support	195
Password Security and Resetting CMOS	196
Resetting the Password Jumper	196
Clearing and Resetting the CMOS	197
Backup and Recovery	199
Windows 7 – Backup and Recovery	199
Backing Up Your Information	199
Performing a Recovery	200
Using the Windows Recovery Tools	201
Using F11	201
Using a Windows 7 Operating System DVD (purchased separately)	202
Specifications	203
MT Specifications	203
SFF Specifications	204

Match case Limit results 1 per page

System setup utility reports unprogrammed EEPROM.

Cause

Solution

Unprogrammed EEPROM.

Contact an authorized service provider.

Solving Memory Problems

If you encounter memory problems, some common causes and solutions are listed in the following

table.

CAUTION:

Power may still be supplied to the DIMMs when the computer is turned off (depending

on the Management Engine (ME) settings). To avoid damage to the DIMMs or the system board, you

must unplug the computer power cord before attempting to reseat, install, or remove a DIMM module.

For those systems that support ECC memory, HP does not support mixing ECC and non-ECC

memory. Otherwise, the computer will not boot the operating system.

NOTE:

The memory count will be affected by configurations with the Management Engine (ME)

enabled. The ME uses 8MB of system memory in single channel mode or 16MB of memory in dual-

channel mode to download, decompress, and execute the ME firmware for Out-of-Band (OOB), third-

party data storage, and other management functions.

Table D-13

Solving Memory Problems

System will not boot or does not function properly after installing additional memory modules.

Cause

Solution

A memory module is not installed in the DIMM1 or XMM1

socket.

Ensure that a memory module is installed in the DIMM1 or

XMM1 socket on the system board. This socket must be

populated with a memory module.

Memory module is not the correct type or speed grade for

the system or the new memory module is not seated

properly.

Replace module with the correct industry-standard device for

the computer. On some models, ECC and non-ECC memory

modules cannot be mixed.

Out of memory error.

Cause

Solution

Memory configuration may not be set up correctly.

Use the Device Manager to check memory configuration.

You have run out of memory to run the application.

Check the application documentation to determine the

memory requirements.

Memory count during POST is wrong.

Cause

Solution

The memory modules may not be installed correctly.

Check that the memory modules have been installed

correctly and that proper modules are used.

Integrated graphics may use system memory.

No action required.

Solving Memory Problems

177