Home » HP Manuals » Desktops » HP Pro 3330 » Manual Viewer

HP Pro 3330 HP Pro 3330 Microtower PC, HP Pro 3330 Small Form Factor PC, and H - Page 27

Recovering the Configuration Settings, command with the Computer Setup F10 Utility.

Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Table 3-6 Computer Setup-Advanced (for advanced users) (continued) Device Options Allows you to set: ● Num Lock State at Power-On (off/on). Default is off. ● Multi-Processor (enable/disable). Use this option to disable multi-processor support under the OS. Default is enabled. ● NIC PXE Option ROM Download (PXE, iSCSI, disabled). The BIOS contains an embedded NIC option ROM to allow the unit to boot through the network to a PXE server. This is typically used to download a corporate image to a hard drive. The NIC option ROM takes up memory space below 1MB commonly referred to as DOS Compatibility Hole (DCH) space. This space is limited. This F10 option will allow users to disable the downloading of this embedded NIC option ROM thus giving more DCH space for additional PCI cards which may need option ROM space. The default will be to have the NIC option-ROM-enabled. Default is PXE. AMT Configuration (some models) Allows you to set: ● AMT (enable/disable). Allows you to enable or disable functions of the embedded Management Engine (ME) such as Active Management Technology (AMT). If set to disable, the Management Engine is set to a temporarily disabled state and will not provide functions beyond necessary system configuration. Default is enabled. ● Unconfigure AMT/ME (enable/disable). Allows you to unconfigure any provisioned management settings for AMT. The AMT settings are restored to factory defaults. This feature should be used with caution as AMT will not be able to provide any set AMT management functions once unconfigured. Default is disabled. ● Watchdog Timer (enable/disable). Allows you to set amount of time for a operating system and BIOS watchdog alert to be sent if the timers are not deactivated. BIOS watchdog is deactivated by BIOS and would indicate that a halt occurred during execution if the alert is sent to the management console. An operating system alert is deactivated by the operating system image and would indicate that a hang occurred during its initialization. Default is enabled. Recovering the Configuration Settings This method of recovery requires that you first perform the Save to Removable Media command with the Computer Setup (F10) Utility before Restore is needed. NOTE: It is recommended that you save any modified computer configuration settings to a USB flash media device and save the device for possible future use. To restore the configuration, insert the USB flash media device with the saved configuration and perform the Restore from Removable Media command with the Computer Setup (F10) Utility. Recovering the Configuration Settings 17

Section	Page
Product Features	11
Identifying the Chassis	11
Serviceability Features	11
Feature Overview	12
Microtower Components	13
Small Form Factor Components	14
Installing and Customizing the Software	15
Installing the Operating System	15
Downloading Microsoft Windows Updates	15
Installing or Upgrading Device Drivers (Windows systems)	16
Accessing Disk Image (ISO) Files	16
Protecting the Software	16
Computer Setup (F10) Utility	17
Computer Setup (F10) Utilities	17
Using Computer Setup (F10) Utilities	18
Computer Setup—File	18
Computer Setup—Storage	20
Computer Setup—Security	22
Computer Setup—Power	25
Computer Setup—Advanced	26
Recovering the Configuration Settings	27
Illustrated parts catalog	28
Microtower (MT) Chassis Spare Parts	28
Computer Major Components	28
Cables	30
Misc Parts	31
Drives	32
Misc Boards	32
Sequential Part Number Listing	32
Small Form Factor (SFF) Chassis Spare Parts	35
Computer major components	35
Cables	37
Misc Parts	38
Drives	38
Misc Boards	39
Sequential Part Number Listing	39
Serial ATA (SATA) Drive Guidelines and Features	42
SATA Hard Drives	42
SATA Hard Drive Cables	42
SATA Data Cable	42
SMART ATA Drives	43
Hard Drive Capacities	43
Routine Care and Disassembly Preparation	44
Electrostatic Discharge Information	44
Generating Static	44
Preventing Electrostatic Damage to Equipment	45
Personal Grounding Methods and Equipment	46
Grounding the Work Area	46
Recommended Materials and Equipment	46
Operating Guidelines	47
Routine Care	48
General Cleaning Safety Precautions	48
Cleaning the Computer Case	48
Cleaning the Keyboard	48
Cleaning the Monitor	49
Cleaning the Mouse	49
Service Considerations	49
Power Supply Fan	49
Tools and Software Requirements	49
Screws	50
Cables and Connectors	50
Hard Drives	50
Lithium Coin Cell Battery	50
Removal and Replacement Procedures – Microtower (MT) Chassis	52
Preparation for Disassembly	52
Access Panel	53
Front Bezel	55
Memory	57
DDR3-SDRAM DIMMs	57
Populating DIMM Sockets	58
Removing Memory Modules	59
Expansion Cards	61
Cable Management	67
Cable Connections	68
Drives	69
Drive Positions	70
Installing Additional Drives	71
System Board Drive Connections	72
Removing an Optical Drive	73
Removing a Hard Drive	76
Front I/O and USB Panel Housing Assembly	83
Power Switch/LED Assembly	85
System Fan	87
Speaker	89
Fan Sink Assembly	90
Processor	92
Power Supply	95
System Board	97
Battery	98
Removal and Replacement Procedures – Small Form Factor (SFF) Chassis	100
Preparation for Disassembly	100
Access Panel	100
Front Bezel	102
Memory	103
DDR3-SDRAM DIMMs	103
Populating DIMM Sockets	104
Removing DIMMs	105
Expansion Card	108
Cable Management	112
Cable Connections	113
Drives	114
Drive Positions	114
Removing Drives	115
Removing an Optical Drive	115
Removing the Hard Drive	117
Power Switch	120
Front USB Assembly	122
Speaker	125
Fan Assembly	126
Fan Sink	129
Processor	131
Power Supply	133
System Board	136
Battery	137
Connector Pin Assignments	139
Ethernet BNC	139
USB	139
Microphone	139
Headphone	139
Line-in Audio	140
Line-out Audio	140
4-Pin Power (for CPU)	140
Monitor	141
Serial Interface, Powered and Non-Powered	141
DVI Connector	142
24-Pin Power	143
PCI Express	144
PCI Express	145
Power Cord Set Requirements	146
General Requirements	146
Japanese Power Cord Requirements	146
Country-Specific Requirements	147
POST Error Messages	148
POST Numeric Codes and Text Messages	148
Interpreting POST Diagnostic Front Panel LEDs and Audible Codes	156
Troubleshooting Without Diagnostics	160
Safety and Comfort	160
Before You Call for Technical Support	160
Helpful Hints	161
Solving General Problems	162
Solving Power Problems	165
Solving Diskette Problems	166
Solving Hard Drive Problems	169
Solving Media Card Reader Problems	172
Solving Display Problems	173
Solving Audio Problems	177
Solving Printer Problems	179
Solving Keyboard and Mouse Problems	180
Solving Hardware Installation Problems	181
Solving Network Problems	183
Solving Memory Problems	187
Solving Processor Problems	188
Solving CD-ROM and DVD Problems	189
Solving USB Flash Drive Problems	191
Solving Front Panel Component Problems	191
Solving Internet Access Problems	192
Solving Software Problems	195
Contacting Customer Support	195
Password Security and Resetting CMOS	196
Resetting the Password Jumper	196
Clearing and Resetting the CMOS	197
Backup and Recovery	199
Windows 7 – Backup and Recovery	199
Backing Up Your Information	199
Performing a Recovery	200
Using the Windows Recovery Tools	201
Using F11	201
Using a Windows 7 Operating System DVD (purchased separately)	202
Specifications	203
MT Specifications	203
SFF Specifications	204

Match case Limit results 1 per page

Table 3-6

Computer Setup—Advanced (for advanced users) (continued)

Device Options

Allows you to set:

●

Num Lock State at Power-On (off/on). Default is off.

●

Multi-Processor (enable/disable). Use this option to disable multi-processor support under

the OS. Default is enabled.

●

NIC PXE Option ROM Download (PXE, iSCSI, disabled). The BIOS contains an embedded

NIC option ROM to allow the unit to boot through the network to a PXE server. This is

typically used to download a corporate image to a hard drive. The NIC option ROM takes up

memory space below 1MB commonly referred to as DOS Compatibility Hole (DCH) space.

This space is limited. This F10 option will allow users to disable the downloading of this

embedded NIC option ROM thus giving more DCH space for additional PCI cards which may

need option ROM space. The default will be to have the NIC option-ROM-enabled. Default is

PXE.

AMT Configuration

(some models)

Allows you to set:

●

AMT (enable/disable). Allows you to enable or disable functions of the embedded

Management Engine (ME) such as Active Management Technology (AMT). If set to disable,

the Management Engine is set to a temporarily disabled state and will not provide functions

beyond necessary system configuration. Default is enabled.

●

Unconfigure AMT/ME (enable/disable). Allows you to unconfigure any provisioned

management settings for AMT. The AMT settings are restored to factory defaults. This

feature should be used with caution as AMT will not be able to provide any set AMT

management functions once unconfigured. Default is disabled.

●

Watchdog Timer (enable/disable). Allows you to set amount of time for a operating system

and BIOS watchdog alert to be sent if the timers are not deactivated. BIOS watchdog is

deactivated by BIOS and would indicate that a halt occurred during execution if the alert is

sent to the management console. An operating system alert is deactivated by the operating

system image and would indicate that a hang occurred during its initialization. Default is

enabled.

Recovering the Configuration Settings

This method of recovery requires that you first perform the

Save to Removable Media

command

with the Computer Setup (F10) Utility before

Restore

is needed.

NOTE:

It is recommended that you save any modified computer configuration settings to a USB

flash media device and save the device for possible future use.

To restore the configuration, insert the USB flash media device with the saved configuration and

perform the

Restore from Removable Media

command with the Computer Setup (F10) Utility.

Recovering the Configuration Settings