HP ProLiant DL185 HP ProLiant DL185 Generation 5 Server Software Configuration - Page 6

Accessing the Setup Utility

Get HP ProLiant DL185 - G5 Server PDF manuals and user guides View all HP ProLiant DL185 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

• When a configuration error is detected by the system and you are prompted by a "Run Setup" message to make changes to the BIOS settings. NOTE: If you repeatedly receive "Run Setup" messages, the battery located on the system board may be defective. In this case, the system cannot retain configuration values in CMOS. Ask a qualified technician for assistance. The Setup Utility loads the configuration values in a battery-backed nonvolatile memory called CMOS RAM. This memory area is not part of the system RAM, which allows configuration data to be retained when power is turned off. The values take effect when the system is booted. POST uses these values to configure the hardware. If the values and the actual hardware do not agree, POST generates an error message. You must run the Setup Utility to change the BIOS settings from the default or current configuration. Accessing the Setup Utility 1. Turn on the monitor and the server. If the server is already turned on, save your data and exit all open applications, then restart the server. During POST, press F10. If you fail to press F10 before POST is completed, you need to restart the server and repeat this step. The first page displayed is the Main menu. Use the left (←) and right (→) arrow keys to move between selections on the menu bar. Figure 1 Main Menu NOTE: System Serial Number and Asset Tag are not updated even when CMOS defaults are loaded or CMOS is cleared. System BIOS configuration 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
System BIOS configuration 6
•
When a configuration error is detected by the system and you are prompted by a "Run Setup"
message to make changes to the BIOS settings.
NOTE:
If you repeatedly receive “Run Setup” messages, the battery located on the system board
may be defective. In this case, the system cannot retain configuration values in CMOS. Ask a
qualified technician for assistance.
The Setup Utility loads the configuration values in a battery-backed nonvolatile memory called CMOS
RAM. This memory area is not part of the system RAM, which allows configuration data to be
retained when power is turned off. The values take effect when the system is booted. POST uses these
values to configure the hardware. If the values and the actual hardware do not agree, POST
generates an error message. You must run the Setup Utility to change the BIOS settings from the
default or current configuration.
Accessing the Setup Utility
1.
Turn on the monitor and the server.
If the server is already turned on, save your data and exit all open applications, then restart the
server.
During POST, press
F10
. If you fail to press
F10
before POST is completed, you need to restart
the server and repeat this step. The first page displayed is the Main menu. Use the left (
←
) and
right (
→
) arrow keys to move between selections on the menu bar.
Figure 1
Main Menu
NOTE:
System Serial Number and Asset Tag are not updated even when CMOS defaults are
loaded or CMOS is cleared.