HP ProLiant DL185 HP ProLiant DL185 Generation 5 Server Software Configuration - Page 60

In the I/O Device Configuration submenu, set the Serial port Mode field to BMC. See the I/O

Get HP ProLiant DL185 - G5 Server PDF manuals and user guides View all HP ProLiant DL185 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

8. At the Password prompt, type your password and press Enter. The default password is admin. 9. The message CLP Session Initiated displays. 10. At the prompt, type cd map1/nic1 to navigate to the correct directory. The command line interface is SMASH-compliant. 11. Type show to display the current settings. 12. Modify the settings you want to change. NOTE: The set variables are case-sensitive. For example, by default, the BMC is set to use DHCP to get the IP address. To manually set the IP address, type set oemhp_dhcp_enable=FALSE to disable DHCP, then type set networkaddress=xxx.xxx.xxx.xxx to set the IP address you want. To revert to using DHCP to set the IP address, type set oemhp_dhcp_enable=TRUE to enable DHCP.The system takes a few seconds to set the new IP address. 13. Open a browser and enter the IP address that you set manually or that was set automatically using DHCP. 14. When prompted, enter the same user name and password you used in your terminal session. 15. Browse the server settings using the user interface that displays. To enable console redirection via the Setup Utility: 1. In the I/O Device Configuration submenu, set the Serial port Mode field to BMC. See the "I/O Device Configuration submenu" section for more information. 2. In the Console Redirection submenu, set the Com Port Address to On Board Com Port A. See the "Console Redirection submenu fields" section for more information. 3. Press F10 to Save and Exit. Server management 60

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
Server management 60
8.
At the Password prompt, type your password and press Enter. The default password is admin.
9.
The message CLP Session Initiated displays.
10.
At the prompt, type cd map1/nic1 to navigate to the correct directory. The command line
interface is SMASH-compliant.
11.
Type show to display the current settings.
12.
Modify the settings you want to change.
NOTE:
The set variables are case-sensitive.
For example, by default, the BMC is set to use DHCP to get the IP address. To manually set the IP
address, type
set oemhp_dhcp_enable=FALSE to disable DHCP, then type set
networkaddress=xxx.xxx.xxx.xxx to set the IP address you want.
To revert to using DHCP to set the IP address, type set oemhp_dhcp_enable=TRUE to enable
DHCP.The system takes a few seconds to set the new IP address.
13.
Open a browser and enter the IP address that you set manually or that was set automatically
using DHCP.
14.
When prompted, enter the same user name and password you used in your terminal session.
15.
Browse the server settings using the user interface that displays.
To enable console redirection via the Setup Utility:
1.
In the I/O Device Configuration submenu, set the Serial port Mode field to BMC. See the “I/O
Device Configuration submenu” section for more information.
2.
In the Console Redirection submenu, set the Com Port Address to On Board Com Port A. See the
“Console Redirection submenu fields” section for more information.
3.
Press F10 to Save and Exit.