HP ProLiant DL388e HP ProLiant DL388e Gen8 Server User Guide - Page 20

Remove the server from the rack

Get HP ProLiant DL388e PDF manuals and user guides View all HP ProLiant DL388e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

For more information, see the documentation that ships with the rack mounting option. 7. Connect the peripheral cables. 8. Connect each power cord to the server. 9. Connect each power cord to the power source. Remove the server from the rack WARNING: This server is very heavy. To reduce the risk of personal injury or damage to the equipment: • Observe local occupational health and safety requirements and guidelines for manual material handling. • Get help to lift and stabilize the product during installation or removal, especially when the product is not fastened to the rails. HP recommends that a minimum of two people are required for all rack server installations. A third person may be required to help align the server if the server is installed higher than chest level. • Use caution when installing the server in or removing the server from the rack; it is unstable when not fastened to the rails. IMPORTANT: The requirement of extending or removing the server from the rack when performing installation and maintenance procedures depends on the rail system used: • If using a ball-bearing rail system, you can perform most installations and maintenance by simply extending the server from the rack. • If using a friction rail system, to perform installations or maintenance that requires access panel removal, remove the server from the rack. To remove the server from an HP, Compaq-branded, Telco, or third-party rack: 1. Power down the server (on page 18). 2. Disconnect all peripheral cables and power cords from the server rear panel. 3. Extend the server from the rack (on page 18). 4. Remove the server from the rack. For more information, see the documentation that ships with the rack mounting option. Operations 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Operations 20
For more information, see the documentation that ships with the rack mounting option.
7.
Connect the peripheral cables.
8.
Connect each power cord to the server.
9.
Connect each power cord to the power source.
Remove the server from the rack
WARNING:
This server is very heavy. To reduce the risk of personal injury or damage to the
equipment:
•
Observe local occupational health and safety requirements and guidelines for manual
material handling.
•
Get help to lift and stabilize the product during installation or removal, especially when the
product is not fastened to the rails. HP recommends that a minimum of two people are required
for all rack server installations. A third person may be required to help align the server if the
server is installed higher than chest level.
•
Use caution when installing the server in or removing the server from the rack; it is unstable
when not fastened to the rails.
IMPORTANT:
The requirement of extending or removing the server from the rack when
performing installation and maintenance procedures depends on the rail system used:
•
If using a ball-bearing rail system, you can perform most installations and maintenance by
simply extending the server from the rack.
•
If using a friction rail system, to perform installations or maintenance that requires access panel
removal, remove the server from the rack.
To remove the server from an HP, Compaq-branded, Telco, or third-party rack:
1.
Power down the server (on page
18
).
2.
Disconnect all peripheral cables and power cords from the server rear panel.
3.
Extend the server from the rack (on page
18
).
4.
Remove the server from the rack. For more information, see the documentation that ships with the rack
mounting option.