HP ProLiant DL388e HP ProLiant DL388e Gen8 Server User Guide - Page 45

Smart Array cables

Get HP ProLiant DL388e PDF manuals and user guides View all HP ProLiant DL388e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

12. Install the server into the rack ("Installing the server into the rack" on page 31). 13. Install the drives ("Drive options" on page 34). CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all bays are populated with either a component or a blank. 14. Power up the server (on page 18). Smart Array cables To connect the cable option: 1. Power down the server (on page 18). 2. Remove all power: a. Disconnect each power cord from the power source. b. Disconnect each power cord from the server. 3. Do one of the following: o Extend the server from the rack (on page 18). o Remove the server from the rack (on page 20). 4. Remove the access panel (on page 21). 5. Remove the air baffle (on page 22). 6. Install the storage controller ("Storage controller installation guidelines" on page 47). 7. Connect the Smart Array cables to the storage controller. 8. Route the Smart Array cables along the side of the system board towards the front chassis, and then connect them to the drive backplane: o Cable routing from the primary PCI riser cage o Cable routing from the secondary PCI riser cage (optional) Hardware options installation 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Hardware options installation 45
12.
Install the server into the rack ("
Installing the server into the rack
" on page
31
).
13.
Install the drives ("
Drive options
" on page
34
).
CAUTION:
To prevent improper cooling and thermal damage, do not operate the server unless
all bays are populated with either a component or a blank.
14.
Power up the server (on page
18
).
Smart Array cables
To connect the cable option:
1.
Power down the server (on page
18
).
2.
Remove all power:
a.
Disconnect each power cord from the power source.
b.
Disconnect each power cord from the server.
3.
Do one of the following:
o
Extend the server from the rack (on page
18
).
o
Remove the server from the rack (on page
20
).
4.
Remove the access panel (on page
21
).
5.
Remove the air baffle (on page
22
).
6.
Install the storage controller ("
Storage controller installation guidelines
" on page
47
).
7.
Connect the Smart Array cables to the storage controller.
8.
Route the Smart Array cables along the side of the system board towards the front chassis, and then
connect them to the drive backplane:
o
Cable routing from the primary PCI riser cage
o
Cable routing from the secondary PCI riser cage (optional)