HP ProLiant DL388e HP ProLiant DL388e Gen8 Server User Guide - Page 63

Installing a DIMM, Install the DIMM.

Get HP ProLiant DL388e PDF manuals and user guides View all HP ProLiant DL388e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

• Each channel can have a different valid online spare configuration. • Each populated channel must have a spare rank: o A single dual-rank DIMM is not a valid configuration. o LRDIMMs are treated as dual-rank DIMMs. Installing a DIMM 1. Power down the server (on page 18). 2. Remove all power: a. Disconnect each power cord from the power source. b. Disconnect each power cord from the server. 3. Do one of the following: o Extend the server from the rack (on page 18). o Remove the server from the rack (on page 20). 4. Remove the access panel (on page 21). 5. Remove the air baffle (on page 22). 6. Open the DIMM slot latches. 7. Install the DIMM. 8. Install the air baffle (on page 22). 9. Install the access panel (on page 21). 10. Install the server into the rack ("Installing the server into the rack" on page 31). 11. Power up the server (on page 18). After installing the DIMMs, use RBSU ("HP ROM-Based Setup Utility" on page 103) to configure the memory protection mode. Hardware options installation 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Hardware options installation 63
•
Each channel can have a different valid online spare configuration.
•
Each populated channel must have a spare rank:
o
A single dual-rank DIMM is not a valid configuration.
o
LRDIMMs are treated as dual-rank DIMMs.
Installing a DIMM
1.
Power down the server (on page
18
).
2.
Remove all power:
a.
Disconnect each power cord from the power source.
b.
Disconnect each power cord from the server.
3.
Do one of the following:
o
Extend the server from the rack (on page
18
).
o
Remove the server from the rack (on page
20
).
4.
Remove the access panel (on page
21
).
5.
Remove the air baffle (on page
22
).
6.
Open the DIMM slot latches.
7.
Install the DIMM.
8.
Install the air baffle (on page
22
).
9.
Install the access panel (on page
21
).
10.
Install the server into the rack ("
Installing the server into the rack
" on page
31
).
11.
Power up the server (on page
18
).
After installing the DIMMs, use RBSU ("
HP ROM-Based Setup Utility
" on page
103
) to configure the memory
protection mode.