Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 415X » Manual Viewer

Husqvarna AUTOMOWER 415X Owner Manual - Page 15

Drive Past, To set the Drive Past Wire, function on To make an, island

View all Husqvarna AUTOMOWER 415X manuals

Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

E D F C 10 cm / 4" max 1 cm / 0.4" A B • Put the boundary wire around all of the work area (A). Adapt the distance between the boundary wire and obstacles. • Put the boundary wire 35 cm / 14 in. (B) from an obstacle that is more than 5 cm / 2 in. high. > 5 cm / 2" • If you have a paving stone path that is in level with the lawn, put the boundary wire below the paving stone. Note: If the paving stone is minimum 30 cm / 12 in. wide, use the factory setting for the Drive Past Wire function to cut all the grass adjacent to the paving stone. Refer to To set the Drive Past Wire function on page 27. • If you make an island, put the boundary wire that runs to and from the island near together (E). Put the wires in the same stake. Refer to To make an island on page 16. • Make an eyelet (F) where the guide wire is to be connected to the boundary wire. 3.4.3.1 To put the boundary wire in a slope The product can operate in 40% slopes. Slopes that are too steep must be isolated with the boundary wire. The gradient (%) is calculated as height per m. Example: 10 cm / 100 cm = 10%. 35 cm /14" • Put the boundary wire 30 cm / 12 in. (C) from an obstacle that is 1-5 cm / 0.4-2 in. high. 10% 10 cm/4" 100 cm/40" • For slopes steeper than 40% inside the work area, isolate the slope with boundary wire. • For slopes steeper than 15% along the outer edge of the lawn, put the boundary wire 20 cm / 8 in. (A) from the edge. 30 cm / 12" 1-5 cm / 0.4 - 2" • Put the boundary wire 10 cm / 4 in. (D) from an obstacle that is less than 1 cm / 0.4 in. high. >10% 0-25% A • For slopes adjacent to a public road, put a barrier of minimum 15 cm / 6 in. along the outer edge of 1650 - 005 - 17.03.2022 Installation - 15

Section	Page
Contents	2
Introduction	3
Introduction	3
Support	3
Product description	3
Mowing technique	3
Find the charging station	3
Automower® Connect	3
Automower® Intellegent Mapping (AIM)	3
Product overview	4
Symbols on the product	5
Symbols on the display	5
Symbols on the battery	6
General manual instructions	6
Menu structure overview - 1	7
Menu structure overview - 2	8
Display	9
Keypad	9
Safety	10
Safety definitions	10
General safety instructions	10
Safety instructions for installation	11
Safety instructions for operation	11
Safety instructions for maintenance	11
Battery safety	11
How to lift and move the product	12
Installation	13
Introduction - Installation	13
Main components for installation	13
General preparations	13
Before the installation of the wires	13
To examine where to put the charging station	13
To examine where to put the power supply	14
To examine where to put the boundary wire	14
To put the boundary wire in a slope	15
Passages	16
To make an island	16
To make a secondary area	16
To examine where to put the guide wire	17
Work area examples	17
Installation of the product	17
Installation tools	17
To install the charging station	18
To install the boundary wire	18
To install the guide wire	18
To put the wire into position with stakes	19
To bury the boundary wire or the guide wire	19
To extend the boundary wire or the guide wire	19
After the installation of the product	20
To do a visual check of the charging station	20
To do the basic settings	20
Product settings	20
Automower® Connect app	20
To install the Automower® Connect app	20
To pair Automower® Connect and the product	21
Automower® Intellegent Mapping (AIM)	21
Download firmware over the air FOTA (Firmware over the air)	21
Product settings with keypad and display	21
To get access to the menu in the display of the product	21
Menu structure	21
Schedule	21
To set the schedule	21
Make an estimate of the necessary operating time	22
To copy the schedule setting	22
To reset the schedule setting	22
Cutting height	22
Adjust the cutting height	22
To set the cutting height	22
TargetHeight	22
To set the TargetHeight	22
Security level	23
To set the security level	23
To create a New loop signal	23
To change the PIN-code	23
To change the duration of the alarm	23
Messages	23
To read the messages	23
Weather timer	23
To set the Weather timer	24
To set the Weather timer frequency	24
Installation	24
GPS Assisted Navigation, Lawn Coverage and Systematic Passage Mowing	24
To set the GPS Assisted Navigation	24
To set the Lawn Coverage function	25
To set the System Passage Mowing function	25
To do a test of the Lawn Coverage function	25
To measure the distance from the charging station	25
To disable or enable the Lawn Coverage function	25
To reset the Lawn Coverage settings	26
Methods for the product to find the charging station	26
To set how the product finds the charging station	26
To do a test of the guide wire	26
To do a test of the boundary wire	26
To change the signal range of the charging station	26
Corridor width	27
To set the corridor width	27
Reversing distance	27
To set the reversing distance	27
Drive Past Wire function	27
To set the Drive Past Wire function	27
Settings	27
ECO mode	27
To set the ECO mode	27
Spiral Cutting	28
To set the Spiral Cutting	28
To set the level of Spiral Cutting	28
General	28
To set the time & date	28
To set the language	28
To set the Country & Timezone	28
To set the unit format	28
To reset all user settings	28
Frost Guard	28
To set the Frost Guard	28
The About menu	29
Accessories	29
Information	29
Automower® Connect	29
To enable the GeoFence function	29
To set a new center point for the Geofence function	29
To set the GeoFence level of sensitivity	29
To avoid collisions with the Automower® house	29
Headlights Automower® 405X/415X	29
To set the schedule for the headlights	29
To set the Flashes when fault function	29
Operation	31
To use the ON/OFF button	31
To start the product	31
Operating modes - Start	31
Main area	31
Secondary area	31
Override schedule	31
Spot cutting	31
To park the product	31
Operating modes - Park	32
Park until further notice	32
Start again with next schedule	32
To stop the product	32
To set the product to OFF	32
To charge the battery	32
Maintenance	33
Introduction - maintenance	33
Clean the product	33
To clean the chassis and blade disc	33
To clean the wheels	34
To clean the body of the product	34
To clean the charging station	34
Replacement of the blades	34
To replace the blades	34
Battery	35
Winter service	35
Troubleshooting	36
Introduction - troubleshooting	36
Fault messages	36
Information and warning messages	41
Indicator lamp in the charging station	42
Symptoms	43
Find breaks in the loop wire	44
Transportation, storage and disposal	47
Transportation	47
Storage	47
Disposal	47
To remove the battery	47
Technical data	48
Automower® 405X/415X	48
Registered trademarks	50
Warranty	51