Husqvarna AUTOMOWER 415X Owner Manual - Page 18

3.5.2 To install the charging station

CAUTION:

Do not make new holes in

the charging station plate.

CAUTION:

Do not put your feet on the

baseplate of the charging station.

WARNING:

Make sure that the plugs of

the low-voltage cable and the power supply

unit are clean and dry before you connect

them.

When connecting the power supply, only use a power

outlet that is connected to an residual-current (RCD)

device.

1.

Read and understand the instructions about the

charging station. Refer to

To examine where to put

the charging station on page 13

.

2.

Put the charging station in the selected area.

Note:

Do not attach the charging station to the

ground with the screws until the guide wire is

installed. Refer to

To install the guide wire on page

18

.

3.

Connect the low-voltage cable to the charging

station.

4.

Put the power supply at a minimum height of 30

cm / 12 in.

min 30 cm / 12”

5.

Connect the power supply cable to a 100-240V

power outlet.

Note:

When the charging station is connected,

it is possible to charge the product. Place the

product in the charging station while the boundary

and guide wires are being laid. Switch on the

product. Do not continue with any product settings

before the installation is complete.

6.

Put the low-voltage cable in the ground with stakes

or bury the cable. Refer to

To put the wire into

position with stakes on page 19

or

To bury the

boundary wire or the guide wire on page 19

.

7.

Connect the wires to the charging station after

the installation of boundary wire and guide wire is

complete. Refer to

To install the boundary wire on

page 18

and

To install the guide wire on page

18

.

8.

Attach the charging station to the ground with the

supplied screws after the guide wire is installed.

Refer to

To install the guide wire on page 18

.

3.5.3 To install the boundary wire

CAUTION:

Do not put remaining wire in

a coil. The coil causes interference with the

product.

1.

Put the boundary wire around all of the work

area. Start and complete the installation behind the

charging station.

2.

Open the connector and put the boundary wire in

the connector.

3.

Close the connector with a pair of pliers.

4.

Cut the boundary wire 1-2 cm / 0.4-0.8 in. above

each connector.

5.

Push the right connector onto the metal pin on the

charging station with the mark "AR".

6.

Push the left connector onto the metal pin on the

charging station with the mark "AL".

3.5.4 To install the guide wire

CAUTION:

Twinned cables, or a

screw terminal block that is insulated with

insulation tape are not satisfactory splices.

Soil moisture will cause the wire to oxidize

and after a time result in a broken circuit.

1.

Open the connector and put the wire in the

connector.

2.

Close the connector with a pair of pliers.

18

- Installation

1650 - 005 - 17.03.2022

Section	Page
Contents	2
Introduction	3
Introduction	3
Support	3
Product description	3
Mowing technique	3
Find the charging station	3
Automower® Connect	3
Automower® Intellegent Mapping (AIM)	3
Product overview	4
Symbols on the product	5
Symbols on the display	5
Symbols on the battery	6
General manual instructions	6
Menu structure overview - 1	7
Menu structure overview - 2	8
Display	9
Keypad	9
Safety	10
Safety definitions	10
General safety instructions	10
Safety instructions for installation	11
Safety instructions for operation	11
Safety instructions for maintenance	11
Battery safety	11
How to lift and move the product	12
Installation	13
Introduction - Installation	13
Main components for installation	13
General preparations	13
Before the installation of the wires	13
To examine where to put the charging station	13
To examine where to put the power supply	14
To examine where to put the boundary wire	14
To put the boundary wire in a slope	15
Passages	16
To make an island	16
To make a secondary area	16
To examine where to put the guide wire	17
Work area examples	17
Installation of the product	17
Installation tools	17
To install the charging station	18
To install the boundary wire	18
To install the guide wire	18
To put the wire into position with stakes	19
To bury the boundary wire or the guide wire	19
To extend the boundary wire or the guide wire	19
After the installation of the product	20
To do a visual check of the charging station	20
To do the basic settings	20
Product settings	20
Automower® Connect app	20
To install the Automower® Connect app	20
To pair Automower® Connect and the product	21
Automower® Intellegent Mapping (AIM)	21
Download firmware over the air FOTA (Firmware over the air)	21
Product settings with keypad and display	21
To get access to the menu in the display of the product	21
Menu structure	21
Schedule	21
To set the schedule	21
Make an estimate of the necessary operating time	22
To copy the schedule setting	22
To reset the schedule setting	22
Cutting height	22
Adjust the cutting height	22
To set the cutting height	22
TargetHeight	22
To set the TargetHeight	22
Security level	23
To set the security level	23
To create a New loop signal	23
To change the PIN-code	23
To change the duration of the alarm	23
Messages	23
To read the messages	23
Weather timer	23
To set the Weather timer	24
To set the Weather timer frequency	24
Installation	24
GPS Assisted Navigation, Lawn Coverage and Systematic Passage Mowing	24
To set the GPS Assisted Navigation	24
To set the Lawn Coverage function	25
To set the System Passage Mowing function	25
To do a test of the Lawn Coverage function	25
To measure the distance from the charging station	25
To disable or enable the Lawn Coverage function	25
To reset the Lawn Coverage settings	26
Methods for the product to find the charging station	26
To set how the product finds the charging station	26
To do a test of the guide wire	26
To do a test of the boundary wire	26
To change the signal range of the charging station	26
Corridor width	27
To set the corridor width	27
Reversing distance	27
To set the reversing distance	27
Drive Past Wire function	27
To set the Drive Past Wire function	27
Settings	27
ECO mode	27
To set the ECO mode	27
Spiral Cutting	28
To set the Spiral Cutting	28
To set the level of Spiral Cutting	28
General	28
To set the time & date	28
To set the language	28
To set the Country & Timezone	28
To set the unit format	28
To reset all user settings	28
Frost Guard	28
To set the Frost Guard	28
The About menu	29
Accessories	29
Information	29
Automower® Connect	29
To enable the GeoFence function	29
To set a new center point for the Geofence function	29
To set the GeoFence level of sensitivity	29
To avoid collisions with the Automower® house	29
Headlights Automower® 405X/415X	29
To set the schedule for the headlights	29
To set the Flashes when fault function	29
Operation	31
To use the ON/OFF button	31
To start the product	31
Operating modes - Start	31
Main area	31
Secondary area	31
Override schedule	31
Spot cutting	31
To park the product	31
Operating modes - Park	32
Park until further notice	32
Start again with next schedule	32
To stop the product	32
To set the product to OFF	32
To charge the battery	32
Maintenance	33
Introduction - maintenance	33
Clean the product	33
To clean the chassis and blade disc	33
To clean the wheels	34
To clean the body of the product	34
To clean the charging station	34
Replacement of the blades	34
To replace the blades	34
Battery	35
Winter service	35
Troubleshooting	36
Introduction - troubleshooting	36
Fault messages	36
Information and warning messages	41
Indicator lamp in the charging station	42
Symptoms	43
Find breaks in the loop wire	44
Transportation, storage and disposal	47
Transportation	47
Storage	47
Disposal	47
To remove the battery	47
Technical data	48
Automower® 405X/415X	48
Registered trademarks	50
Warranty	51

Husqvarna AUTOMOWER 415X Owner Manual - Page 18

Caution, Warning

Page 18 highlights