Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 415X » Manual Viewer

Husqvarna AUTOMOWER 415X Owner Manual - Page 37

Message, Cause, Action

View all Husqvarna AUTOMOWER 415X manuals

Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Message Cause Action Wheel motor blocked, left/right Grass or other object is wrapped around the Clean the wheels and around the wheels. drive wheel. Wheel motor overloaded, left/right Wheel drive problem, right/left Cutting system blocked Grass or other object is wrapped around the Clean the wheels and around the wheels. drive wheel. The blade disc lies in a pool of water. Move the product and prevent the collection of water in the work area. The grass is too high. Cut the grass before you install the product. Make sure that the grass is maximum 10 cm / 3.9 in. Cutting system imbal- Too few or too many blades. ance Do a check of the blades on the blade disc. Outside working area The boundary wire connections to the charg- Check that the boundary wire is connected ing station are crossed. correctly. The boundary wire is too close to the edge of the work area. The work area slopes too much by the boundary loop. Check that the boundary wire has been laid according to the instructions. Refer to To install the boundary wire on page 18. The boundary wire is laid in the wrong direction around an island. Disturbances from metal objects (fences, re- Try moving the boundary wire. inforcement steel) or buried cables close by. The product finds it hard to distinguish the Put the product in the charging station and signal from another product installation close generate a new loop signal. by. Slope too steep The product stopped because the slope is too steep. Change the installation of the boundary wire to not include this steep part of the work area. Refer to To put the boundary wire in a slope on page 15. Empty battery The product cannot find the charging station. Change the position of the guide wire. Refer to To install the guide wire on page 18. The battery is at the end of its life cycle. Replace the battery. Refer to Battery on page 35. The charging station's antenna is defective. Check if the indicator lamp in the charging station flashes red. Refer to Indicator lamp in the charging station on page 42. The charging plates on the product or contact plates on the charging station are corroded. Clean the charging and contact plates using a fine grade emery cloth. If the problem stays speak to your authorized service technician. 1650 - 005 - 17.03.2022 Troubleshooting - 37

Section	Page
Contents	2
Introduction	3
Introduction	3
Support	3
Product description	3
Mowing technique	3
Find the charging station	3
Automower® Connect	3
Automower® Intellegent Mapping (AIM)	3
Product overview	4
Symbols on the product	5
Symbols on the display	5
Symbols on the battery	6
General manual instructions	6
Menu structure overview - 1	7
Menu structure overview - 2	8
Display	9
Keypad	9
Safety	10
Safety definitions	10
General safety instructions	10
Safety instructions for installation	11
Safety instructions for operation	11
Safety instructions for maintenance	11
Battery safety	11
How to lift and move the product	12
Installation	13
Introduction - Installation	13
Main components for installation	13
General preparations	13
Before the installation of the wires	13
To examine where to put the charging station	13
To examine where to put the power supply	14
To examine where to put the boundary wire	14
To put the boundary wire in a slope	15
Passages	16
To make an island	16
To make a secondary area	16
To examine where to put the guide wire	17
Work area examples	17
Installation of the product	17
Installation tools	17
To install the charging station	18
To install the boundary wire	18
To install the guide wire	18
To put the wire into position with stakes	19
To bury the boundary wire or the guide wire	19
To extend the boundary wire or the guide wire	19
After the installation of the product	20
To do a visual check of the charging station	20
To do the basic settings	20
Product settings	20
Automower® Connect app	20
To install the Automower® Connect app	20
To pair Automower® Connect and the product	21
Automower® Intellegent Mapping (AIM)	21
Download firmware over the air FOTA (Firmware over the air)	21
Product settings with keypad and display	21
To get access to the menu in the display of the product	21
Menu structure	21
Schedule	21
To set the schedule	21
Make an estimate of the necessary operating time	22
To copy the schedule setting	22
To reset the schedule setting	22
Cutting height	22
Adjust the cutting height	22
To set the cutting height	22
TargetHeight	22
To set the TargetHeight	22
Security level	23
To set the security level	23
To create a New loop signal	23
To change the PIN-code	23
To change the duration of the alarm	23
Messages	23
To read the messages	23
Weather timer	23
To set the Weather timer	24
To set the Weather timer frequency	24
Installation	24
GPS Assisted Navigation, Lawn Coverage and Systematic Passage Mowing	24
To set the GPS Assisted Navigation	24
To set the Lawn Coverage function	25
To set the System Passage Mowing function	25
To do a test of the Lawn Coverage function	25
To measure the distance from the charging station	25
To disable or enable the Lawn Coverage function	25
To reset the Lawn Coverage settings	26
Methods for the product to find the charging station	26
To set how the product finds the charging station	26
To do a test of the guide wire	26
To do a test of the boundary wire	26
To change the signal range of the charging station	26
Corridor width	27
To set the corridor width	27
Reversing distance	27
To set the reversing distance	27
Drive Past Wire function	27
To set the Drive Past Wire function	27
Settings	27
ECO mode	27
To set the ECO mode	27
Spiral Cutting	28
To set the Spiral Cutting	28
To set the level of Spiral Cutting	28
General	28
To set the time & date	28
To set the language	28
To set the Country & Timezone	28
To set the unit format	28
To reset all user settings	28
Frost Guard	28
To set the Frost Guard	28
The About menu	29
Accessories	29
Information	29
Automower® Connect	29
To enable the GeoFence function	29
To set a new center point for the Geofence function	29
To set the GeoFence level of sensitivity	29
To avoid collisions with the Automower® house	29
Headlights Automower® 405X/415X	29
To set the schedule for the headlights	29
To set the Flashes when fault function	29
Operation	31
To use the ON/OFF button	31
To start the product	31
Operating modes - Start	31
Main area	31
Secondary area	31
Override schedule	31
Spot cutting	31
To park the product	31
Operating modes - Park	32
Park until further notice	32
Start again with next schedule	32
To stop the product	32
To set the product to OFF	32
To charge the battery	32
Maintenance	33
Introduction - maintenance	33
Clean the product	33
To clean the chassis and blade disc	33
To clean the wheels	34
To clean the body of the product	34
To clean the charging station	34
Replacement of the blades	34
To replace the blades	34
Battery	35
Winter service	35
Troubleshooting	36
Introduction - troubleshooting	36
Fault messages	36
Information and warning messages	41
Indicator lamp in the charging station	42
Symptoms	43
Find breaks in the loop wire	44
Transportation, storage and disposal	47
Transportation	47
Storage	47
Disposal	47
To remove the battery	47
Technical data	48
Automower® 405X/415X	48
Registered trademarks	50
Warranty	51

Match case Limit results 1 per page

Message

Cause

Action

Wheel motor

blocked, left/right

Grass or other object is wrapped around the

drive wheel.

Clean the wheels and around the wheels.

Wheel motor overloa-

ded, left/right

Wheel drive problem,

right/left

Cutting system

blocked

Grass or other object is wrapped around the

drive wheel.

Clean the wheels and around the wheels.

The blade disc lies in a pool of water.

Move the product and prevent the collection

of water in the work area.

The grass is too high.

Cut the grass before you install the product.

Make sure that the grass is maximum 10

cm / 3.9 in.

Cutting system imbal-

ance

Too few or too many blades.

Do a check of the blades on the blade disc.

Outside working area

The boundary wire connections to the charg-

ing station are crossed.

Check that the boundary wire is connected

correctly.

The boundary wire is too close to the edge of

the work area.

Check that the boundary wire has been laid

according to the instructions. Refer to

To in-

stall the boundary wire on page 18

The work area slopes too much by the boun-

dary loop.

The boundary wire is laid in the wrong direc-

tion around an island.

Disturbances from metal objects (fences, re-

inforcement steel) or buried cables close by.

Try moving the boundary wire.

The product finds it hard to distinguish the

signal from another product installation close

by.

Put the product in the charging station and

generate a new loop signal.

Slope too steep

The product stopped because the slope is

too steep.

Change the installation of the boundary wire

to not include this steep part of the work

area. Refer to

To put the boundary wire in

a slope on page 15

Empty battery

The product cannot find the charging station.

Change the position of the guide wire. Refer

To install the guide wire on page 18

The battery is at the end of its life cycle.

Replace the battery. Refer to

Battery on

page 35

The charging station’s antenna is defective.

Check if the indicator lamp in the charging

station flashes red. Refer to

Indicator lamp in

the charging station on page 42

The charging plates on the product or con-

tact plates on the charging station are corro-

ded.

Clean the charging and contact plates using

a fine grade emery cloth. If the problem stays

speak to your authorized service technician.

1650 - 005 - 17.03.2022

Troubleshooting -