Husqvarna AUTOMOWER 415X Owner Manual - Page 22

6.

Calculate the suitable operating hours. Refer to

Make an estimate of the necessary operating time

on page 22

.

7.

Enter the time with the

number

buttons. The

product can cut the grass 1 or 2 periods each day.

8.

If the product must not cut grass on a specified

day, unselect the box adjacent to the 2 time

periods.

3.12.3.2 Make an estimate of the necessary operating

time

If the work area is less than maximum product capacity,

the schedule must be set to decrease the wear on the

lawn and the product. The product has a maximum

cutting time each day. You can set the operating time of

the product in the schedule. The operating time includes

cutting, searching and charging. The operating time can

be different because of many reasons, for example the

layout of the work area, the grass growth and age of the

battery. When the product has operated to the maximum

cutting time in a day, the message

Today's mowing

complete

is shown in the display of the product.

The recommended operating times for some work area

examples are shown in the table below. If the result is

not satisfactory, increase the operating time.

Area, m

2

Recommended operating

time, h

500

10

1000

17

1500

24

3.12.3.3 To copy the schedule setting

1.

Do steps 1–3 in

To get access to the menu in the

display of the product on page 21

.

2.

Use the

arrow

buttons and the

OK

button to move

through the menu structure

Schedule > Overview >

Copy

.

3.

Use the

arrow

buttons and the

OK

button to copy

the schedule setting. You can copy the schedule

settings day to day or for the full week.

3.12.3.4 To reset the schedule setting

You can remove all schedule settings and use the

factory setting.

1.

Do steps 1–3 in



.

2.

Use the

arrow

buttons and the

OK

button to move

through the menu structure

Schedule > Overview >

Reset

.

a)

Push the

arrow

buttons to select

Current

day

to only reset the current day to factory

settings.

b)

Push the

arrow

buttons to select

All week

to

reset all schedule settings to factory settings.

3.

Push the

OK

button.

3.12.4 Cutting height

3.12.4.1 Adjust the cutting height

CAUTION:

During the first weeks after

a new installation, the cutting height must be

set to MAX to avoid damaging the loop wire.

After this, the cutting height can be lowered

step by step every week until the desired

cutting height has been reached.

The cutting height can be varied from MIN (2 cm / 0.8

in.) to MAX (5 cm / 2 in.).

To set the cutting height

1.

Do steps 1–3 in



.

2.

Use the

arrow

buttons and the

OK

button to

move through the menu structure

Cutting height

>

Cutting height

.

3.

Use the

arrow

buttons to set the cutting height.

4.

Push the

OK

button.

3.12.4.2 TargetHeight

Use the TargetHeight function to lower the cutting height

from MAX to the specified cutting height gradually during

10 days. If you change the cutting height manually

during this time it will disable the TargetHeight function.

To set the TargetHeight

1.

Do steps 1–3 in



.

2.

Use the arrow buttons and the

OK

button to

move through the menu structure

Cutting height

>

TargetHeight

.

3.

Push the

OK

button to enable or disable the

function.

22

- Installation

1650 - 005 - 17.03.2022

Section	Page
Contents	2
Introduction	3
Introduction	3
Support	3
Product description	3
Mowing technique	3
Find the charging station	3
Automower® Connect	3
Automower® Intellegent Mapping (AIM)	3
Product overview	4
Symbols on the product	5
Symbols on the display	5
Symbols on the battery	6
General manual instructions	6
Menu structure overview - 1	7
Menu structure overview - 2	8
Display	9
Keypad	9
Safety	10
Safety definitions	10
General safety instructions	10
Safety instructions for installation	11
Safety instructions for operation	11
Safety instructions for maintenance	11
Battery safety	11
How to lift and move the product	12
Installation	13
Introduction - Installation	13
Main components for installation	13
General preparations	13
Before the installation of the wires	13
To examine where to put the charging station	13
To examine where to put the power supply	14
To examine where to put the boundary wire	14
To put the boundary wire in a slope	15
Passages	16
To make an island	16
To make a secondary area	16
To examine where to put the guide wire	17
Work area examples	17
Installation of the product	17
Installation tools	17
To install the charging station	18
To install the boundary wire	18
To install the guide wire	18
To put the wire into position with stakes	19
To bury the boundary wire or the guide wire	19
To extend the boundary wire or the guide wire	19
After the installation of the product	20
To do a visual check of the charging station	20
To do the basic settings	20
Product settings	20
Automower® Connect app	20
To install the Automower® Connect app	20
To pair Automower® Connect and the product	21
Automower® Intellegent Mapping (AIM)	21
Download firmware over the air FOTA (Firmware over the air)	21
Product settings with keypad and display	21
To get access to the menu in the display of the product	21
Menu structure	21
Schedule	21
To set the schedule	21
Make an estimate of the necessary operating time	22
To copy the schedule setting	22
To reset the schedule setting	22
Cutting height	22
Adjust the cutting height	22
To set the cutting height	22
TargetHeight	22
To set the TargetHeight	22
Security level	23
To set the security level	23
To create a New loop signal	23
To change the PIN-code	23
To change the duration of the alarm	23
Messages	23
To read the messages	23
Weather timer	23
To set the Weather timer	24
To set the Weather timer frequency	24
Installation	24
GPS Assisted Navigation, Lawn Coverage and Systematic Passage Mowing	24
To set the GPS Assisted Navigation	24
To set the Lawn Coverage function	25
To set the System Passage Mowing function	25
To do a test of the Lawn Coverage function	25
To measure the distance from the charging station	25
To disable or enable the Lawn Coverage function	25
To reset the Lawn Coverage settings	26
Methods for the product to find the charging station	26
To set how the product finds the charging station	26
To do a test of the guide wire	26
To do a test of the boundary wire	26
To change the signal range of the charging station	26
Corridor width	27
To set the corridor width	27
Reversing distance	27
To set the reversing distance	27
Drive Past Wire function	27
To set the Drive Past Wire function	27
Settings	27
ECO mode	27
To set the ECO mode	27
Spiral Cutting	28
To set the Spiral Cutting	28
To set the level of Spiral Cutting	28
General	28
To set the time & date	28
To set the language	28
To set the Country & Timezone	28
To set the unit format	28
To reset all user settings	28
Frost Guard	28
To set the Frost Guard	28
The About menu	29
Accessories	29
Information	29
Automower® Connect	29
To enable the GeoFence function	29
To set a new center point for the Geofence function	29
To set the GeoFence level of sensitivity	29
To avoid collisions with the Automower® house	29
Headlights Automower® 405X/415X	29
To set the schedule for the headlights	29
To set the Flashes when fault function	29
Operation	31
To use the ON/OFF button	31
To start the product	31
Operating modes - Start	31
Main area	31
Secondary area	31
Override schedule	31
Spot cutting	31
To park the product	31
Operating modes - Park	32
Park until further notice	32
Start again with next schedule	32
To stop the product	32
To set the product to OFF	32
To charge the battery	32
Maintenance	33
Introduction - maintenance	33
Clean the product	33
To clean the chassis and blade disc	33
To clean the wheels	34
To clean the body of the product	34
To clean the charging station	34
Replacement of the blades	34
To replace the blades	34
Battery	35
Winter service	35
Troubleshooting	36
Introduction - troubleshooting	36
Fault messages	36
Information and warning messages	41
Indicator lamp in the charging station	42
Symptoms	43
Find breaks in the loop wire	44
Transportation, storage and disposal	47
Transportation	47
Storage	47
Disposal	47
To remove the battery	47
Technical data	48
Automower® 405X/415X	48
Registered trademarks	50
Warranty	51

Husqvarna AUTOMOWER 415X Owner Manual - Page 22

Cutting height

Page 22 highlights