Husqvarna AUTOMOWER 415X Owner Manual - Page 23

4.

Push the

BACK

button.

3.12.5 Security level

There are 3 security levels for the product.

Function

Low

Medium

High

PIN code

X

X

STOP button

pressed

X

Carried away

X

•

PIN-code

- The correct PIN-code must be entered

to get access to the menu structure of the product.

If the incorrect PIN-code is entered 5 times, the

product is locked for a time. The lock is extended

for each new incorrect try.

•

STOP button pressed

- The alarm goes off if the

STOP

button has been pushed and the PIN code

is not entered in less than 30 seconds.

•

Carried away

- The alarm goes off if the product is

lifted.

3.12.5.1 To set the security level

Select 1 of 3 security levels for your product.

1.

Do steps 1–3 in

To get access to the menu in the

display of the product on page 21

.

2.

Use the

arrow buttons

and the

OK

button to move

through the menu structure

Settings > Security >

Security level

.

3.

Use the

arrow buttons

and the

OK

button to select

the level of security.

4.

Push the

OK

button.

3.12.5.2 To create a New loop signal

The loop signal is randomly selected to create a unique

link between the product and the charging station. In

rare cases, there may be a need to generate a new

signal, for instance if two adjacent installations have a

very similar signal.

1.

Place the product in the charging station.

2.

Do steps 1–3 in



.

3.

Use the

arrow

buttons and the

OK

button to move


Security > Advanced >

New loop signal

.

4.

Await confirmation that the loop signal has been

generated. This normally takes about 10 seconds.

3.12.5.3 To change the PIN-code

1.

Do steps 1–3 in



.

2.

Use the

arrow

buttons and the

OK

button to move


Settings > Security >

Advanced > Change PIN-code

.

3.

Enter the new PIN code.

4.

Push the

OK

button.

5.

Enter the new PIN code again.

6.

Push the

OK

button.

7.

Make a note of the new PIN code. Refer to

Introduction on page 3

.

3.12.5.4 To change the duration of the alarm

1.

Do steps 1–3 in



.

2.

Use the

arrow buttons

and the

OK

button to move


Security > Advanced >

Duration > Duration of alarm

.

3.

Use the

arrow buttons

to select a time interval of 1

to 20 minutes.

4.

Push the

BACK

button.

3.12.6 Messages

In this menu the previous fault and information

messages can be found. For some of the messages,

there are tips and advice to help to rectify the fault.

Refer to

Troubleshooting on page 36

.

If the product is disrupted in any way, for example it

is trapped or the battery is low, a message is saved

relating to the disruption and the time it happened.

If the same message is repeated several times, this

may indicate that an adjustment to the installation or the

product is required. Refer to

Installation on page 13

.

3.12.6.1 To read the messages

1.

Do steps 1–3 in



.

2.

Use the

arrow

buttons and the

OK

button to move


Messages > Fault

messages

and

Messages > Info messages

.

3.

Read the messages and read the

Troubleshooting

to get information and recommendations to correct

the faults.

3.12.7 Weather timer

Weather timer

automatically adjust the cutting time to

the growth of the grass. The product is not permitted to

operate more than the schedule settings.

1650 - 005 - 17.03.2022

Installation -

23

Section	Page
Contents	2
Introduction	3
Introduction	3
Support	3
Product description	3
Mowing technique	3
Find the charging station	3
Automower® Connect	3
Automower® Intellegent Mapping (AIM)	3
Product overview	4
Symbols on the product	5
Symbols on the display	5
Symbols on the battery	6
General manual instructions	6
Menu structure overview - 1	7
Menu structure overview - 2	8
Display	9
Keypad	9
Safety	10
Safety definitions	10
General safety instructions	10
Safety instructions for installation	11
Safety instructions for operation	11
Safety instructions for maintenance	11
Battery safety	11
How to lift and move the product	12
Installation	13
Introduction - Installation	13
Main components for installation	13
General preparations	13
Before the installation of the wires	13
To examine where to put the charging station	13
To examine where to put the power supply	14
To examine where to put the boundary wire	14
To put the boundary wire in a slope	15
Passages	16
To make an island	16
To make a secondary area	16
To examine where to put the guide wire	17
Work area examples	17
Installation of the product	17
Installation tools	17
To install the charging station	18
To install the boundary wire	18
To install the guide wire	18
To put the wire into position with stakes	19
To bury the boundary wire or the guide wire	19
To extend the boundary wire or the guide wire	19
After the installation of the product	20
To do a visual check of the charging station	20
To do the basic settings	20
Product settings	20
Automower® Connect app	20
To install the Automower® Connect app	20
To pair Automower® Connect and the product	21
Automower® Intellegent Mapping (AIM)	21
Download firmware over the air FOTA (Firmware over the air)	21
Product settings with keypad and display	21
To get access to the menu in the display of the product	21
Menu structure	21
Schedule	21
To set the schedule	21
Make an estimate of the necessary operating time	22
To copy the schedule setting	22
To reset the schedule setting	22
Cutting height	22
Adjust the cutting height	22
To set the cutting height	22
TargetHeight	22
To set the TargetHeight	22
Security level	23
To set the security level	23
To create a New loop signal	23
To change the PIN-code	23
To change the duration of the alarm	23
Messages	23
To read the messages	23
Weather timer	23
To set the Weather timer	24
To set the Weather timer frequency	24
Installation	24
GPS Assisted Navigation, Lawn Coverage and Systematic Passage Mowing	24
To set the GPS Assisted Navigation	24
To set the Lawn Coverage function	25
To set the System Passage Mowing function	25
To do a test of the Lawn Coverage function	25
To measure the distance from the charging station	25
To disable or enable the Lawn Coverage function	25
To reset the Lawn Coverage settings	26
Methods for the product to find the charging station	26
To set how the product finds the charging station	26
To do a test of the guide wire	26
To do a test of the boundary wire	26
To change the signal range of the charging station	26
Corridor width	27
To set the corridor width	27
Reversing distance	27
To set the reversing distance	27
Drive Past Wire function	27
To set the Drive Past Wire function	27
Settings	27
ECO mode	27
To set the ECO mode	27
Spiral Cutting	28
To set the Spiral Cutting	28
To set the level of Spiral Cutting	28
General	28
To set the time & date	28
To set the language	28
To set the Country & Timezone	28
To set the unit format	28
To reset all user settings	28
Frost Guard	28
To set the Frost Guard	28
The About menu	29
Accessories	29
Information	29
Automower® Connect	29
To enable the GeoFence function	29
To set a new center point for the Geofence function	29
To set the GeoFence level of sensitivity	29
To avoid collisions with the Automower® house	29
Headlights Automower® 405X/415X	29
To set the schedule for the headlights	29
To set the Flashes when fault function	29
Operation	31
To use the ON/OFF button	31
To start the product	31
Operating modes - Start	31
Main area	31
Secondary area	31
Override schedule	31
Spot cutting	31
To park the product	31
Operating modes - Park	32
Park until further notice	32
Start again with next schedule	32
To stop the product	32
To set the product to OFF	32
To charge the battery	32
Maintenance	33
Introduction - maintenance	33
Clean the product	33
To clean the chassis and blade disc	33
To clean the wheels	34
To clean the body of the product	34
To clean the charging station	34
Replacement of the blades	34
To replace the blades	34
Battery	35
Winter service	35
Troubleshooting	36
Introduction - troubleshooting	36
Fault messages	36
Information and warning messages	41
Indicator lamp in the charging station	42
Symptoms	43
Find breaks in the loop wire	44
Transportation, storage and disposal	47
Transportation	47
Storage	47
Disposal	47
To remove the battery	47
Technical data	48
Automower® 405X/415X	48
Registered trademarks	50
Warranty	51

Husqvarna AUTOMOWER 415X Owner Manual - Page 23

Security level, 12.6 Messages, 12.7 Weather timer

Page 23 highlights