Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 415X » Manual Viewer

Husqvarna AUTOMOWER 415X Owner Manual - Page 43

Symptoms

View all Husqvarna AUTOMOWER 415X manuals

Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

6.5 Symptoms If the product does not operate as usual, follow the symptoms table below. Speak to your Husqvarna customer service if you cannot find the cause for the fault. Symptoms Cause Action The product has diffi- The guide wire is not put straight in a line culty docking. and correct distance from the charging station. Do a check of the installation of the charging station. Refer to To install the charging station on page 18 The guide wire is not put in the slot in the charging station plate. Make sure that the guide wire is put straight in a line and put in the slot in the charging station plate. Refer to To install the guide wire on page 18. The charging station is not on a level surface. Put the charging station on a level surface. Refer to To examine where to put the charging station on page 13. The product operates The time or the date in the product is not at the wrong time correct. Set the time or date. Refer to To set the time & date on page 28. The start and stop times for operating are incorrect. Change the Schedule settings. Refer to Schedule on page 21. The product vibrates. The cutting system is not in balance because Examine the blades and screws and replace of damaged blades. them if necessary. Refer to Replacement of the blades on page 34. The cutting system is not in balance because Do a check that only one blade is attached at of too many blades in the same position. each screw. Different thickness of blades are installed on Do a check if the blades are of different thick- the product. ness and replace if necessary. The product operates, but the blade disc does not rotate. The product searches for the charging station, or is moving to the starting point. Usual operation for the product. The blade disc does not rotate when the product is searching for the charging station. The product operates for shorter periods than usual between charges. Grass or other object causes a blockage to the blade disc. The battery is at the end of its life cycle. Remove and clean the blade disc. Refer to To clean the chassis and blade disc on page 33. Replace the battery. Refer to Battery on page 35. Blunt blades. More energy is necessary when cutting the grass. Replace the blades. Refer to Replacement of the blades on page 34. Mowing and charging times are shorter than usual. The battery is at the end of its life cycle. Replace the battery. Refer to Battery on page 35. 1650 - 005 - 17.03.2022 Troubleshooting - 43

Section	Page
Contents	2
Introduction	3
Introduction	3
Support	3
Product description	3
Mowing technique	3
Find the charging station	3
Automower® Connect	3
Automower® Intellegent Mapping (AIM)	3
Product overview	4
Symbols on the product	5
Symbols on the display	5
Symbols on the battery	6
General manual instructions	6
Menu structure overview - 1	7
Menu structure overview - 2	8
Display	9
Keypad	9
Safety	10
Safety definitions	10
General safety instructions	10
Safety instructions for installation	11
Safety instructions for operation	11
Safety instructions for maintenance	11
Battery safety	11
How to lift and move the product	12
Installation	13
Introduction - Installation	13
Main components for installation	13
General preparations	13
Before the installation of the wires	13
To examine where to put the charging station	13
To examine where to put the power supply	14
To examine where to put the boundary wire	14
To put the boundary wire in a slope	15
Passages	16
To make an island	16
To make a secondary area	16
To examine where to put the guide wire	17
Work area examples	17
Installation of the product	17
Installation tools	17
To install the charging station	18
To install the boundary wire	18
To install the guide wire	18
To put the wire into position with stakes	19
To bury the boundary wire or the guide wire	19
To extend the boundary wire or the guide wire	19
After the installation of the product	20
To do a visual check of the charging station	20
To do the basic settings	20
Product settings	20
Automower® Connect app	20
To install the Automower® Connect app	20
To pair Automower® Connect and the product	21
Automower® Intellegent Mapping (AIM)	21
Download firmware over the air FOTA (Firmware over the air)	21
Product settings with keypad and display	21
To get access to the menu in the display of the product	21
Menu structure	21
Schedule	21
To set the schedule	21
Make an estimate of the necessary operating time	22
To copy the schedule setting	22
To reset the schedule setting	22
Cutting height	22
Adjust the cutting height	22
To set the cutting height	22
TargetHeight	22
To set the TargetHeight	22
Security level	23
To set the security level	23
To create a New loop signal	23
To change the PIN-code	23
To change the duration of the alarm	23
Messages	23
To read the messages	23
Weather timer	23
To set the Weather timer	24
To set the Weather timer frequency	24
Installation	24
GPS Assisted Navigation, Lawn Coverage and Systematic Passage Mowing	24
To set the GPS Assisted Navigation	24
To set the Lawn Coverage function	25
To set the System Passage Mowing function	25
To do a test of the Lawn Coverage function	25
To measure the distance from the charging station	25
To disable or enable the Lawn Coverage function	25
To reset the Lawn Coverage settings	26
Methods for the product to find the charging station	26
To set how the product finds the charging station	26
To do a test of the guide wire	26
To do a test of the boundary wire	26
To change the signal range of the charging station	26
Corridor width	27
To set the corridor width	27
Reversing distance	27
To set the reversing distance	27
Drive Past Wire function	27
To set the Drive Past Wire function	27
Settings	27
ECO mode	27
To set the ECO mode	27
Spiral Cutting	28
To set the Spiral Cutting	28
To set the level of Spiral Cutting	28
General	28
To set the time & date	28
To set the language	28
To set the Country & Timezone	28
To set the unit format	28
To reset all user settings	28
Frost Guard	28
To set the Frost Guard	28
The About menu	29
Accessories	29
Information	29
Automower® Connect	29
To enable the GeoFence function	29
To set a new center point for the Geofence function	29
To set the GeoFence level of sensitivity	29
To avoid collisions with the Automower® house	29
Headlights Automower® 405X/415X	29
To set the schedule for the headlights	29
To set the Flashes when fault function	29
Operation	31
To use the ON/OFF button	31
To start the product	31
Operating modes - Start	31
Main area	31
Secondary area	31
Override schedule	31
Spot cutting	31
To park the product	31
Operating modes - Park	32
Park until further notice	32
Start again with next schedule	32
To stop the product	32
To set the product to OFF	32
To charge the battery	32
Maintenance	33
Introduction - maintenance	33
Clean the product	33
To clean the chassis and blade disc	33
To clean the wheels	34
To clean the body of the product	34
To clean the charging station	34
Replacement of the blades	34
To replace the blades	34
Battery	35
Winter service	35
Troubleshooting	36
Introduction - troubleshooting	36
Fault messages	36
Information and warning messages	41
Indicator lamp in the charging station	42
Symptoms	43
Find breaks in the loop wire	44
Transportation, storage and disposal	47
Transportation	47
Storage	47
Disposal	47
To remove the battery	47
Technical data	48
Automower® 405X/415X	48
Registered trademarks	50
Warranty	51

Match case Limit results 1 per page

6.5 Symptoms

If the product does not operate as usual, follow the symptoms table below. Speak to your Husqvarna customer

service if you cannot find the cause for the fault.

Symptoms

Cause

Action

The product has diffi-

culty docking.

The guide wire is not put straight in a line

and correct distance from the charging sta-

tion.

Do a check of the installation of the charging

station. Refer to

To install the charging sta-

tion on page 18

The guide wire is not put in the slot in the

charging station plate.

Make sure that the guide wire is put straight

in a line and put in the slot in the charging

station plate. Refer to

To install the guide

wire on page 18

The charging station is not on a level sur-

face.

Put the charging station on a level surface.

Refer to

To examine where to put the charg-

ing station on page 13

The product operates

at the wrong time

The time or the date in the product is not

correct.

Set the time or date. Refer to

To set the time

& date on page 28

The start and stop times for operating are

incorrect.

Change the

Schedule

settings. Refer to

Schedule on page 21

The product vibrates.

The cutting system is not in balance because

of damaged blades.

Examine the blades and screws and replace

them if necessary. Refer to

Replacement of

the blades on page 34

The cutting system is not in balance because

of too many blades in the same position.

Do a check that only one blade is attached at

each screw.

Different thickness of blades are installed on

the product.

Do a check if the blades are of different thick-

ness and replace if necessary.

The product oper-

ates, but the blade

disc does not rotate.

The product searches for the charging sta-

tion, or is moving to the starting point.

Usual operation for the product. The blade

disc does not rotate when the product is

searching for the charging station.

The product operates

for shorter periods

than usual between

charges.

Grass or other object causes a blockage to

the blade disc.

Remove and clean the blade disc. Refer to

To clean the chassis and blade disc on page

The battery is at the end of its life cycle.

Replace the battery. Refer to

Battery on

page 35

Blunt blades. More energy is necessary

when cutting the grass.

Replace the blades. Refer to

Replacement of

the blades on page 34

Mowing and charg-

ing times are shorter

than usual.

The battery is at the end of its life cycle.

Replace the battery. Refer to

Battery on

page 35

1650 - 005 - 17.03.2022

Troubleshooting -