Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 415X » Manual Viewer

Husqvarna AUTOMOWER 415X Owner Manual - Page 38

Alarm! Outside geo

View all Husqvarna AUTOMOWER 415X manuals

Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Message Cause Action Battery problem Temporary battery or firmware related issue Restart the product. If the problem stays in the product. speak to your authorized service technician. Incorrect type of battery. Use original batteries recommended by the manufacturer. Battery temperature The temperature in the battery is too high or No action. The product will start to operate outside limits too low to start operation. when the temperature is in limits. Wrong PIN code Wrong PIN code has been entered. Five attempts are permitted, and the keypad is then blocked for a period of time. Enter the correct PIN code. If the PIN code is incorrect, use the link in the app to send the PIN code to your registered e-mail address. If you have not registered the e-mail adress, contact your local Husqvarna representative. No drive Slipped The product has got caught in something and Free the product and rectify the reason for has been slipping. the lack of drive. If it is due to wet grass, wait until the lawn has dried before using the product. The work area includes a steep slope. Steep slopes should be isolated. Refer to To put the boundary wire in a slope on page 15. The guide wire is not laid diagonally in the slope. Make sure that the guide wire is installed diagonally across the slope. Refer to To make a secondary area on page 16. Collision sensor problem, front/rear Collision The drive wheels on the product are blocked. Free the product and correct the cause of problem. If the problem stays, speak to your authorized service technichian Alarm! Mower switch- The alarm is activated because the product Adjust the security level in the Security ed off had been switched off. menu. Refer to Security level on page 23. Alarm! Mower stop- The alarm is activated because the product ped has been stopped. Alarm! Mower lifted The alarm is activated because the product has been lifted. Alarm! Mower tilted The alarm is activated because the product has been tilted. Alarm! Mower was moved The alarm is activated because the product has been lifted. Alarm! Outside geo- The alarm was activated because the prod- fence uct was outside its GeoFence. 38 - Troubleshooting 1650 - 005 - 17.03.2022

Section	Page
Contents	2
Introduction	3
Introduction	3
Support	3
Product description	3
Mowing technique	3
Find the charging station	3
Automower® Connect	3
Automower® Intellegent Mapping (AIM)	3
Product overview	4
Symbols on the product	5
Symbols on the display	5
Symbols on the battery	6
General manual instructions	6
Menu structure overview - 1	7
Menu structure overview - 2	8
Display	9
Keypad	9
Safety	10
Safety definitions	10
General safety instructions	10
Safety instructions for installation	11
Safety instructions for operation	11
Safety instructions for maintenance	11
Battery safety	11
How to lift and move the product	12
Installation	13
Introduction - Installation	13
Main components for installation	13
General preparations	13
Before the installation of the wires	13
To examine where to put the charging station	13
To examine where to put the power supply	14
To examine where to put the boundary wire	14
To put the boundary wire in a slope	15
Passages	16
To make an island	16
To make a secondary area	16
To examine where to put the guide wire	17
Work area examples	17
Installation of the product	17
Installation tools	17
To install the charging station	18
To install the boundary wire	18
To install the guide wire	18
To put the wire into position with stakes	19
To bury the boundary wire or the guide wire	19
To extend the boundary wire or the guide wire	19
After the installation of the product	20
To do a visual check of the charging station	20
To do the basic settings	20
Product settings	20
Automower® Connect app	20
To install the Automower® Connect app	20
To pair Automower® Connect and the product	21
Automower® Intellegent Mapping (AIM)	21
Download firmware over the air FOTA (Firmware over the air)	21
Product settings with keypad and display	21
To get access to the menu in the display of the product	21
Menu structure	21
Schedule	21
To set the schedule	21
Make an estimate of the necessary operating time	22
To copy the schedule setting	22
To reset the schedule setting	22
Cutting height	22
Adjust the cutting height	22
To set the cutting height	22
TargetHeight	22
To set the TargetHeight	22
Security level	23
To set the security level	23
To create a New loop signal	23
To change the PIN-code	23
To change the duration of the alarm	23
Messages	23
To read the messages	23
Weather timer	23
To set the Weather timer	24
To set the Weather timer frequency	24
Installation	24
GPS Assisted Navigation, Lawn Coverage and Systematic Passage Mowing	24
To set the GPS Assisted Navigation	24
To set the Lawn Coverage function	25
To set the System Passage Mowing function	25
To do a test of the Lawn Coverage function	25
To measure the distance from the charging station	25
To disable or enable the Lawn Coverage function	25
To reset the Lawn Coverage settings	26
Methods for the product to find the charging station	26
To set how the product finds the charging station	26
To do a test of the guide wire	26
To do a test of the boundary wire	26
To change the signal range of the charging station	26
Corridor width	27
To set the corridor width	27
Reversing distance	27
To set the reversing distance	27
Drive Past Wire function	27
To set the Drive Past Wire function	27
Settings	27
ECO mode	27
To set the ECO mode	27
Spiral Cutting	28
To set the Spiral Cutting	28
To set the level of Spiral Cutting	28
General	28
To set the time & date	28
To set the language	28
To set the Country & Timezone	28
To set the unit format	28
To reset all user settings	28
Frost Guard	28
To set the Frost Guard	28
The About menu	29
Accessories	29
Information	29
Automower® Connect	29
To enable the GeoFence function	29
To set a new center point for the Geofence function	29
To set the GeoFence level of sensitivity	29
To avoid collisions with the Automower® house	29
Headlights Automower® 405X/415X	29
To set the schedule for the headlights	29
To set the Flashes when fault function	29
Operation	31
To use the ON/OFF button	31
To start the product	31
Operating modes - Start	31
Main area	31
Secondary area	31
Override schedule	31
Spot cutting	31
To park the product	31
Operating modes - Park	32
Park until further notice	32
Start again with next schedule	32
To stop the product	32
To set the product to OFF	32
To charge the battery	32
Maintenance	33
Introduction - maintenance	33
Clean the product	33
To clean the chassis and blade disc	33
To clean the wheels	34
To clean the body of the product	34
To clean the charging station	34
Replacement of the blades	34
To replace the blades	34
Battery	35
Winter service	35
Troubleshooting	36
Introduction - troubleshooting	36
Fault messages	36
Information and warning messages	41
Indicator lamp in the charging station	42
Symptoms	43
Find breaks in the loop wire	44
Transportation, storage and disposal	47
Transportation	47
Storage	47
Disposal	47
To remove the battery	47
Technical data	48
Automower® 405X/415X	48
Registered trademarks	50
Warranty	51

Match case Limit results 1 per page

Message

Cause

Action

Battery problem

Temporary battery or firmware related issue

in the product.

Restart the product. If the problem stays

speak to your authorized service technician.

Incorrect type of battery.

Use original batteries recommended by the

manufacturer.

Battery temperature

outside limits

The temperature in the battery is too high or

too low to start operation.

No action. The product will start to operate

when the temperature is in limits.

Wrong PIN code

Wrong PIN code has been entered. Five at-

tempts are permitted, and the keypad is then

blocked for a period of time.

Enter the correct PIN code. If the PIN code is

incorrect, use the link in the app to send the

PIN code to your registered e-mail address.

If you have not registered the e-mail adress,

contact your local Husqvarna representative.

No drive

Slipped

The product has got caught in something and

has been slipping.

Free the product and rectify the reason for

the lack of drive. If it is due to wet grass,

wait until the lawn has dried before using the

product.

The work area includes a steep slope.

Steep slopes should be isolated. Refer to

put the boundary wire in a slope on page 15

The guide wire is not laid diagonally in the

slope.

Make sure that the guide wire is installed di-

agonally across the slope. Refer to

To make

a secondary area on page 16

Collision sensor

problem, front/rear

Collision

The drive wheels on the product are blocked.

Free the product and correct the cause of

problem. If the problem stays, speak to your

authorized service technichian

Alarm! Mower switch-

ed off

The alarm is activated because the product

had been switched off.

Adjust the security level in the

Security

menu. Refer to

Security level on page 23

Alarm! Mower stop-

ped

The alarm is activated because the product

has been stopped.

Alarm! Mower lifted

The alarm is activated because the product

has been lifted.

Alarm! Mower tilted

The alarm is activated because the product

has been tilted.

Alarm! Mower was

moved

The alarm is activated because the product

has been lifted.

Alarm! Outside geo-

fence

The alarm was activated because the prod-

uct was outside its

GeoFence

- Troubleshooting

1650 - 005 - 17.03.2022