Husqvarna AUTOMOWER 415X Owner Manual - Page 28

3.12.9.2 Spiral Cutting

The product cuts the grass in a spiral pattern if the grass

is longer in an area.

Spiral cutting

can be set in 5 levels:

•

Low-

•

Low

•

Mid

•

High

•

High+

The level sets how sensitive the product is to changes in

grass height.

Note:

Spiral cutting

is only started in the Main area

mode. Cutting in the

Secondary area

mode does not let

the product to start

Spiral cutting

.

Spiral Cutting

does not

start in slopes steeper than 15%.

To set the Spiral Cutting

1.

Do steps 1–3 in

To get access to the menu in the

display of the product on page 21

.

2.

Use the

arrow buttons

and the

OK

button to

move through the menu structure

Settings > Spiral

Cutting > Use Spiral Cutting

.

3.

Push the

BACK

button.

To set the level of Spiral Cutting

1.

Do steps 1–3 in



.

2.

Use the

arrow buttons

and the

OK

button to

move through the menu structure

Settings > Spiral

Cutting > Use Spiral Cutting > Intensity

.

3.

Use the left

arrow button

to select the level of the

Spiral Cutting.

4.

Push the

BACK

button.

3.12.9.3 General

In

General

you can change the general settings of the

product.

To set the time & date

1.

Do steps 1–3 in



.

2.

Use the

arrow

buttons and the

OK

button to move

through the menu structure

Settings > General >

Time & Date

.

3.

Use the

number

buttons to set the time and then

push the

BACK

button.

4.

Use the

number

buttons to set the date and then

push the

BACK

button.

5.

Use the

arrow

buttons to set the time format and

then push the

BACK

button.

6.

Use the

arrow

buttons to set the date format and

then push the

BACK

button.

To set the language

1.

Do steps 1–3 in



.

2.

Use the

arrow

buttons and the

OK

button to move



Language.

3.

Use the

arrow

buttons to select language and then

push the

BACK

button.

To set the Country & Timezone

1.

Do steps 1–3 in



.

2.

Use the

arrow

buttons and the

OK

button to move



Country & Timezone.

3.

Use the

arrow

buttons to select country and then

push the

BACK

button.

To set the unit format

1.

Do steps 1–3 in



.

2.

Use the

arrow

buttons and the

OK

button to move



Unit format.

3.

Use the

arrow

buttons to select unit format and

then push the

BACK

button.

To reset all user settings

1.

Do steps 1–3 in



.

2.

Use the

arrow

buttons and the

OK

button to move



Reset all user settings

.

3.

Use the right

arrow

button to select

Proceed with

reset of all user settings?

4.

Push the

OK

button to reset all the user settings.

Note:

Security level, PIN code, Loop signal,

Messages, Date & Time, Language

and

Country

settings

are not reset.

Frost Guard

The grass is extra sensitive to wear if the yard is

covered with frost. If the

Frost Guard

is activated, the

product is not allowed to start to cut the grass if the

temperature is below 5° C / 41° F.

Note:

The frost sensor is located inside the chassis

and there can be a delay compared to the ambient

temperature.

To set the Frost Guard

1.

Do steps 1–3 in



.

28

- Installation

1650 - 005 - 17.03.2022

Section	Page
Contents	2
Introduction	3
Introduction	3
Support	3
Product description	3
Mowing technique	3
Find the charging station	3
Automower® Connect	3
Automower® Intellegent Mapping (AIM)	3
Product overview	4
Symbols on the product	5
Symbols on the display	5
Symbols on the battery	6
General manual instructions	6
Menu structure overview - 1	7
Menu structure overview - 2	8
Display	9
Keypad	9
Safety	10
Safety definitions	10
General safety instructions	10
Safety instructions for installation	11
Safety instructions for operation	11
Safety instructions for maintenance	11
Battery safety	11
How to lift and move the product	12
Installation	13
Introduction - Installation	13
Main components for installation	13
General preparations	13
Before the installation of the wires	13
To examine where to put the charging station	13
To examine where to put the power supply	14
To examine where to put the boundary wire	14
To put the boundary wire in a slope	15
Passages	16
To make an island	16
To make a secondary area	16
To examine where to put the guide wire	17
Work area examples	17
Installation of the product	17
Installation tools	17
To install the charging station	18
To install the boundary wire	18
To install the guide wire	18
To put the wire into position with stakes	19
To bury the boundary wire or the guide wire	19
To extend the boundary wire or the guide wire	19
After the installation of the product	20
To do a visual check of the charging station	20
To do the basic settings	20
Product settings	20
Automower® Connect app	20
To install the Automower® Connect app	20
To pair Automower® Connect and the product	21
Automower® Intellegent Mapping (AIM)	21
Download firmware over the air FOTA (Firmware over the air)	21
Product settings with keypad and display	21
To get access to the menu in the display of the product	21
Menu structure	21
Schedule	21
To set the schedule	21
Make an estimate of the necessary operating time	22
To copy the schedule setting	22
To reset the schedule setting	22
Cutting height	22
Adjust the cutting height	22
To set the cutting height	22
TargetHeight	22
To set the TargetHeight	22
Security level	23
To set the security level	23
To create a New loop signal	23
To change the PIN-code	23
To change the duration of the alarm	23
Messages	23
To read the messages	23
Weather timer	23
To set the Weather timer	24
To set the Weather timer frequency	24
Installation	24
GPS Assisted Navigation, Lawn Coverage and Systematic Passage Mowing	24
To set the GPS Assisted Navigation	24
To set the Lawn Coverage function	25
To set the System Passage Mowing function	25
To do a test of the Lawn Coverage function	25
To measure the distance from the charging station	25
To disable or enable the Lawn Coverage function	25
To reset the Lawn Coverage settings	26
Methods for the product to find the charging station	26
To set how the product finds the charging station	26
To do a test of the guide wire	26
To do a test of the boundary wire	26
To change the signal range of the charging station	26
Corridor width	27
To set the corridor width	27
Reversing distance	27
To set the reversing distance	27
Drive Past Wire function	27
To set the Drive Past Wire function	27
Settings	27
ECO mode	27
To set the ECO mode	27
Spiral Cutting	28
To set the Spiral Cutting	28
To set the level of Spiral Cutting	28
General	28
To set the time & date	28
To set the language	28
To set the Country & Timezone	28
To set the unit format	28
To reset all user settings	28
Frost Guard	28
To set the Frost Guard	28
The About menu	29
Accessories	29
Information	29
Automower® Connect	29
To enable the GeoFence function	29
To set a new center point for the Geofence function	29
To set the GeoFence level of sensitivity	29
To avoid collisions with the Automower® house	29
Headlights Automower® 405X/415X	29
To set the schedule for the headlights	29
To set the Flashes when fault function	29
Operation	31
To use the ON/OFF button	31
To start the product	31
Operating modes - Start	31
Main area	31
Secondary area	31
Override schedule	31
Spot cutting	31
To park the product	31
Operating modes - Park	32
Park until further notice	32
Start again with next schedule	32
To stop the product	32
To set the product to OFF	32
To charge the battery	32
Maintenance	33
Introduction - maintenance	33
Clean the product	33
To clean the chassis and blade disc	33
To clean the wheels	34
To clean the body of the product	34
To clean the charging station	34
Replacement of the blades	34
To replace the blades	34
Battery	35
Winter service	35
Troubleshooting	36
Introduction - troubleshooting	36
Fault messages	36
Information and warning messages	41
Indicator lamp in the charging station	42
Symptoms	43
Find breaks in the loop wire	44
Transportation, storage and disposal	47
Transportation	47
Storage	47
Disposal	47
To remove the battery	47
Technical data	48
Automower® 405X/415X	48
Registered trademarks	50
Warranty	51

Husqvarna AUTOMOWER 415X Owner Manual - Page 28

Cutting > Use Spiral Cutting > Intensity

Page 28 highlights