IBM QS21 Service Guide - Page 110

error, messages

Page 110 highlights

Table 20. BMC firmware messages (continued) Event Severity Message Cell BE processor 0 over Warning recommended Voltage (1,25V) Cell BE processor 0 under Warning recommended Voltage (0,92V) Cell BE processor 1 over Warning recommended Voltage (1,25V) Cell BE processor 1 under Warning recommended Voltage (0,92V) Processor 1 (CPU 1/2 VCORE) over recommended voltage Processor 1 (CPU 1/2 VCORE) under recommended voltage Processor 2 (CPU 1/2 VCORE) over recommended voltage Processor 2 (CPU 1/2 VCORE) under recommended voltage Automatic Action by BMC None None None None Action required by user No action required. Planar Events Voltage fault Error Voltage+-10% (not BE voltage) Error Planar voltage fault Power Off + ″Voltage Fault #x″, where x is a bit field showing the state of all the voltage signals Blade voltage fault None Reboot. If the error condition continues, report the exact error message to IBM service. - Other Events NMI reset button on Front panel pressed Boot WDT Timeout (Firmware Corrupted) Error Warning Front panel critical Interrupt Firmware BIOS ROM Corruption detected Soft-Reset Reboot & Switch to the permanent flash side DIAGS: Invalid PCI-X Card Error PCI-X card not supported None None. This is a user-initiated action. Reinstall TEMP image. See "Recovering the system firmware code" on page 59 for further information. No power on, PCI-X expansion card needs to be replaced NMI error messages The following messages are placed in the Advanced Management Module error log. Note: The system halts if any of the errors listed below occur. 92 BladeCenter QS21 Type 0792: Problem Determination and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144

Table
20.
BMC
firmware
messages
(continued)
Event
Severity
Message
Automatic
Action
by
BMC
Action
required
by
user
Cell
BE
processor
0
over
recommended
Voltage
(1,25V)
Warning
Processor
1
(CPU
1/2
VCORE)
over
recommended
voltage
None
No
action
required.
Cell
BE
processor
0
under
recommended
Voltage
(0,92V)
Warning
Processor
1
(CPU
1/2
VCORE)
under
recommended
voltage
None
Cell
BE
processor
1
over
recommended
Voltage
(1,25V)
Warning
Processor
2
(CPU
1/2
VCORE)
over
recommended
voltage
None
Cell
BE
processor
1
under
recommended
Voltage
(0,92V)
Warning
Processor
2
(CPU
1/2
VCORE)
under
recommended
voltage
None
Planar
Events
Voltage
fault
Error
Planar
voltage
fault
+
Voltage
Fault
#x
,
where
x
is
a
bit
field
showing
the
state
of
all
the
voltage
signals
Power
Off
Reboot.
If
the
error
condition
continues,
report
the
exact
error
message
to
IBM
service.
Voltage+-10%
(not
BE
voltage)
Error
Blade
voltage
fault
None
-
Other
Events
NMI
reset
button
on
Front
panel
pressed
Error
Front
panel
critical
Interrupt
Soft-Reset
None.
This
is
a
user-initiated
action.
Boot
WDT
Timeout
(Firmware
Corrupted)
Warning
Firmware
BIOS
ROM
Corruption
detected
Reboot
&
Switch
to
the
permanent
flash
side
Reinstall
TEMP
image.
See
“Recovering
the
system
firmware
code”
on
page
59
for
further
information.
DIAGS:
Invalid
PCI-X
Card
Error
PCI-X
card
not
supported
None
No
power
on,
PCI-X
expansion
card
needs
to
be
replaced
NMI
error
messages
The
following
messages
are
placed
in
the
Advanced
Management
Module
error
log.
Note:
The
system
halts
if
any
of
the
errors
listed
below
occur.
92
BladeCenter
QS21
Type
0792:
Problem
Determination
and
Service
Guide