Icom IC-7410 Instruction Manual - Page 110

14 CONTROL COMMAND 103 D Command table (continued) Cmd. Sub cmd. Data Description 16 42 00 Send/read Repeater tone OFF 01 Send/read Repeater tone ON 43 00 Send/read Tone squelch OFF 01 Send/read Tone squelch ON 44 00 Send/read Speech Compressor OFF 01 Send/read Speech Compressor ON 45 00 Send/read Monitor function OFF 01 Send/read Monitor function ON 46 00 Send/read VOX function OFF 01 Send/read VOX function ON 47 00 Send/read BK-IN function OFF 01 Send/read Semi BK-IN function ON 02 Send/read Full BK-IN function ON 48 00 Send/read Manual Notch function OFF 01 Send/read Manual Notch function ON 4C 00 Send/read VSC function OFF 01 Send/read VSC function ON 4F 00 Send/read Twin Peak Filter OFF 01 Send/read Twin Peak Filter ON 50 00 Send/read Dial Lock function OFF 01 Send/read Dial Lock function ON 55 00 Send/read 1st IF filter 15 kHz 01 Send/read 1st IF filter 6 kHz 02 Send/read 1st IF filter 3 kHz 56 00 Send/read DSP filter type SHARP 01 Send/read DSP filter type SOFT 57 00 Send/read manual notch width WIDE 01 Send/read manual notch width MID 02 Send/read manual notch width NAR 58 00 Send/read SSB transmit bandwidth WIDE 01 Send/read SSB transmit bandwidth MID 02 Send/read SSB transmit bandwidth NAR 17 see p. 107 Send CW messages 19 00 Read the transceiver ID 1A 00 see p. 108 Send/read memory contents 01 see p. 106 Send/read band stacking register contents 02 see p. 107 Send/read memory keyer contents 03 00 to 49 Send/read the selected filter width (AM: 00=200 Hz to 49=10 kHz; other than AM modes: 00=50 Hz to 40/31=3600 Hz/2700 Hz) 04 00 to 13 Send/read the selected AGC time constant (00=OFF, AM: 01=0.3 sec. to 13=8.0 sec.; other than AM modes: 01=0.1 sec. to 13=6.0 sec.) 05 0001 0000 to Send/read LCD contrast 0255 (0000=0% (low) to 0255=100% (high)) 0002 0000 to Send/read LCD backlight brightness level 0255 (0000=0% (dark) to 0255=100% (bright)) 0003 0000 to Send/read beep level 0255 (0000=0% to 0255=100%) 0004 00 Send/read beep level limit OFF 01 Send/read beep level limit ON 0005 00 Send/read confirmation beep OFF 01 Send/read confirmation beep ON 0006 00 Send/read band edge beep OFF 01 Send/read band edge beep ON (Beep sounds with a default band) 02 Send/read band edge beep with user setting ON 03 Send/read band edge beep with user setting/TX limit ON 0007 0050 to Send/read beep audio frequency 0200 (0050=500 Hz to 0200=2000 Hz) Cmd. Sub cmd. Data Description 1A 05 0008 00 Send/read Auto selection for [RF/SQL] 01 Send/read SQL selection for [RF/SQL] 0009 02 Send/read RF+SQL selection for [RF/SQL] 00 Send/read Meter Peak Hold function OFF 01 Send/read Meter Peak Hold function ON 0010 00 Send/read Time-Out Timer (CI-V) OFF 01 Send/read 3 min. Time-Out Timer (CI-V) 02 Send/read 5 min. Time-Out Timer (CI-V) 03 Send/read 10 min. Time-Out Timer (CI-V) 04 Send/read 20 min. Time-Out Timer (CI-V) 05 Send/read 30 min. Time-Out Timer (CI-V) 0011 00 Send/read Quick Split function OFF 01 Send/read Quick Split function ON 0012 see p. 107 Send/read FM Split offset frequency (HF) 0013 see p. 107 Send/read FM Split offset frequency (50 MHz) 0014 00 Send/read Split Lock function OFF 01 Send/read Split Lock function ON 0015 00 Send/read Tuner Auto Start OFF 01 Send/read Tuner Auto Start ON 0016 00 Send/read PTT Tune OFF 01 Send/read PTT Tune ON 0017 00 Send/read antenna selection OFF 01 Send/read manual antenna selection 02 Send/read auto antenna selection 0018 0000 to Send/read voice synthesizer level 0255 (0000=0% to 0255=100%) 0019 00 Send/read English selection for voice synthesizer speech language 01 Send/read Japanese selection for voice synthesizer speech language 0020 00 Send/read speech speed slow 01 Send/read speech speed fast 0021 00 Send/read S-meter level announcement OFF 01 Send/read S-meter level announcement ON 0022 00 Send/read operating mode announcement (after pushing mode switch) OFF 01 Send/read operating mode announcement (after pushing mode switch) ON 0023 00 Send/read number of memo pad channels 5 01 Send/read number of memo pad channels 10 0024 00 Send/read auto TS for [DIAL] OFF 01 Send/read auto TS for [DIAL] Low 0025 02 Send/read auto TS for [DIAL] High 00 Send/read Low selection for microphone Up/Down speed 01 Send/read High selection for microphone Up/Down speed 0026 00 Send/read Quick RIT/∂TX clear OFF 01 Send/read Quick RIT/∂TX clear ON 0027 00 Send/read Auto Notch selection for SSB 01 Send/read Manual Notch selection for SSB 02 Send/read Auto/Manual Notch selection for SSB 0028 00 Send/read Auto Notch selection for AM 01 Send/read Manual Notch selection for AM 02 Send/read Auto/Manual Notch selection for AM 0029 00 Send/read manual notch filter width popup OFF 01 Send/read manual notch filter width popup ON