Icom IC-7410 Instruction Manual - Page 12
Transmit Frequency Check Switch [xfc], Up/down Switches, Split Switch [split], Keypad Operation
![]() |
View all Icom IC-7410 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 12 highlights
1 PANEL DESCRIPTION ■ Front panel (continued) #83 #4#5#6 #7 #8 #9 $0 $1 $2 $3 $4 $5 $6 $7 #3 T RANSMIT FREQUENCY CHECK SWITCH [XFC] ➥ During split frequency or repeater operation, hold down to listen to the transmit frequency. (pp. 52, 56) • While holding down this switch, the transmit frequency can be changed with [DIAL], keypad or memo pad. • When the Split Lock function is turned ON, push [XFC] to cancel the Dial Lock function. (p. 67) ➥ When the RIT function is turned ON, hold down to listen to the displayed frequency (RIT is temporarily cancelled). (p. 53) ➥ When the ∂TX function is turned ON, hold down to listen to the transmit frequency (including ∂TX frequency offset). (p. 65) #4 UP/DOWN SWITCHES [Y]/[Z] ➥ Push to change the operating channel. (p. 69) ➥ Hold down to continuously change the operating channel. #5 VFO EQUALIZE SWITCH [A=B] (p. 24) H old down for 1 second to equalize frequencies of VFO A and B. #8 BAND KEYS/KEYPAD BAND KEYS Operation (p. 25) ➥ Push to select the operating band. • [GENE •] selects the general coverage band. ➥ Pushing the same key two or three times calls up other stacked frequencies in the frequency band. • Icom's triple band stacking register memorizes three frequencies in each frequency band. KEYPAD Operation (p. 26) After pushing [F-INP ENT], push the keys on the keypad to enter a frequency. After entering, push [F-INP ENT] to set the frequency. • Example; to enter 14.195 MHz: Push [F-INP ENT] [1] [4] [•] [1] [9] [5] [F-INP ENT]. #9 PBT CLEAR SWITCH [PBT-CLR] (p. 59) (Mode: SSB/CW/RTTY/AM) ➥ Push to display the filter passband width and shifting value for 2 seconds on the function display. ➥ Hold down for 1 second to reset the PBT settings. #6 VFO SELECT SWITCH [A/B] (p. 24) P ush to select either VFO A or VFO B to display. • "VFOA" or "VFOB" is displayed, depending on the selection. $0 P ASSBAND TUNING CONTROLS [TWIN-PBT] (p. 59) (Mode: SSB/CW/RTTY/AM) Adjusts the receiver's IF filter passband width using #7 SPLIT SWITCH [SPLIT] ➥ Push to turn the Split function ON or OFF. (p. 66) • "SPLIT" appears when the Split function is ON. ➥ Hold down for 1 second to activate the Quick Split function. (p. 67) • The transmit frequency shifts from the receive frequency according to the "FM SPLIT Offset HF/50" setting in the Set mode. (p. 86) • The Quick Split function can be turned OFF in the "Quick SPLIT" item of the Set mode. (p. 86) the DSP circuit. • Rotate this control or push [PBT-CLR] to display the PBT settings (passband width and shifting value) for 2 seconds on the function display. • Hold down [PBT-CLR] for 1 second to clear the PBT settings. • The adjustment range is half of the passband width, and the value is adjustable in 25 Hz steps in the SSB, CW, and RTTY modes, and 100 Hz steps in the AM mode. • These controls function as an IF shift control. 5
![](/manual_guide/products/icom-ic7410-instruction-manual-6fdb052/12.png)