Icom IC-7410 Instruction Manual - Page 85

Programmed scan/Fine programmed scan VFO mode

Get Icom IC-7410 PDF manuals and user guides View all Icom IC-7410 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

SCANS 8 ■ Programmed scan/Fine programmed scan (VFO mode) A programmed scan searches for signals between Program Scan Edge channels "P1" and "P2." Before starting the programmed scan, scan edges must be programmed into these channels. Refer to "■ Memory Channel programming" to program Program Scan Edge channels. (p. 70) If the same frequencies are programmed into the Program Scan Edge channels, the programmed scan will not start. q P ush [VFO/MEMO] to select the VFO mode. w P ush a mode switch to select the desired operating mode (p. ). • The operating mode can also be changed while scan- ning. e P ush [TS] one or more times to select a tuning step. (p. 27) • The tuning step can also be changed while scanning. r P ush [MENU] once or twice to display the "M2" screen (Menu 2). t P ush [SCAN](F-1) to display the "SCAN" screen. y R otate the [RF/SQL] control to set the squelch to open or closed. • The scan performance differs, depending on the squelch setting when the scan was started. See page 76 for details. • If the [RF/SQL] control function is set to "AUTO," the squelch is always open in the SSB, CW and RTTY modes. (pp. 2, 32, 86) u P ush [PRO](F-1) to start or cancel the programmed scan. • The MHz and kHz decimal points, and "PROG SCAN" blink while scanning. • Rotating [DIAL] also cancels the scan. [SCAN]/[PRO] [VFO/MEMO] [TS] [RF/SQL] [MENU] Mode switches SCAN PRO ∂F ∂F: ±10k F I N SPAN S E T SCAN PROG SCAN PRO ∂F F I N SPAN S E T While Programmed scanning D About the Fine programmed scan When a signal is received during Fine programmed scan, the scanning tuning step is temporarily set to 10 Hz and the scan speed decreases. q Start the programmed scan. • Follow steps q through u as described above. w W hile scanning, push [FIN](F-3) to switch the scan function between a programmed scan and a Fine programmed scan. • "F-PROG SCAN" blinks while Fine programmed scanning. e Push [PRO](F-1) to cancel the scan. • Rotating [DIAL] also cancels the scan. SCAN PROG SCAN PRO ∂F F I N SPAN S E T SCAN F−PROG SCAN PRO ∂F F I N SPAN S E T While Fine programmed scanning 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 78

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
78
SCANS
1
2
3
4
5
6
7
9
10
12
13
14
15
16
17
18
19
20
21
11
8
8
A programmed scan searches for signals between
Program Scan Edge channels “P1” and “P2.”
Before starting the programmed scan, scan edges
must be programmed into these channels.
Refer to “
■
Memory Channel programming” to pro-
gram Program Scan Edge channels. (p. 70)
If the same frequencies are programmed into the
Program Scan Edge channels, the programmed
scan will not start.
q
Push [VFO/MEMO] to select the VFO mode.
w
Push a mode switch to select the desired operating
mode (p. ).
• The operating mode can also be changed while scan
-
ning.
e
Push [TS] one or more times to select a tuning step.
(p. 27)
• The tuning step can also be changed while scanning.
r
P
ush [MENU] once or twice to display the “M2”
screen (Menu 2).
t
P
ush [SCAN](F-1) to display the “SCAN” screen.
y
Rotate the [RF/SQL] control to set the squelch to
open or closed.
• The scan performance differs, depending on the squelch
setting when the scan was started. See page 76 for de-
tails.
• If the [RF/SQL] control function is set to “AUTO,” the
squelch is always open in the SSB, CW and RTTY
modes. (pp. 2, 32, 86)
u
Push [PRO](F-1) to start or cancel the programmed
scan.
• The MHz and kHz decimal points, and “PROG SCAN”
blink while scanning.
• Rotating [DIAL] also cancels the scan.
■
Programmed scan/Fine programmed scan (VFO mode)
D
About the Fine programmed scan
When a signal is received during Fine programmed
scan, the scanning tuning step is temporarily set to
10 Hz and the scan speed decreases.
q
Start the programmed scan.
• Follow steps
q
through
u
as described above.
w
While scanning, push [FIN](F-3) to switch the scan
function between a programmed scan and a Fine
programmed scan.
• “F-PROG SCAN” blinks while Fine programmed scan
-
ning.
e
Push [PRO](F-1) to cancel the scan.
• Rotating [DIAL] also cancels the scan.
[SCAN]/[PRO]
[VFO/MEMO] [TS]
[MENU]
[RF/SQL]
Mode switches
While Programmed scanning
PRO
∂
F
SPAN
SET
FIN
SCAN
∂
F
:
±
10k
PRO
∂
F
SPAN
SET
FIN
SCAN
PROG
SCAN
PRO
∂
F
SPAN
SET
FIN
SCAN
PROG
SCAN
PRO
∂
F
SPAN
SET
FIN
SCAN
F-PROG
SCAN
While Fine programmed scanning