Icom IC-7410 Instruction Manual - Page 95
MN-Q Popup MN
![]() |
View all Icom IC-7410 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 95 highlights
SET MODE 10 27. MIC Up/Down Speed (Default: HIGH) Set the rate at which frequencies are scanned while holding down the microphone [UP]/[DN] switches. • LOW : Low speed (25 tuning steps/second) • HIGH : High speed (50 tuning steps/second) 33. BW Popup (FIL) (Default: ON) Turn the IF filter passband width and shift value display ON or OFF. When this item set to ON, and [FILTER] is pushed, the passband width and shifting value appear on the function display. 28. Quick RIT Clear (Default: OFF) 34. SSB/CW Sync Tuning (Default: OFF) Select the RIT/∂TX frequency offset clearing opera- Turn the Displayed Frequency Shift function ON or tion with [CLEAR]. OFF. When this function is turned ON, the audio pitch or 1 • OFF : H olding down [CLEAR] for 1 second clears the RIT and ∂TX frequency offset. tones of the received signal will remain the same, even when the operating mode is changed between SSB 2 • ON : Pushing [CLEAR] instantly clears the RIT and ∂TX frequency offset. and CW. The amount of frequency shift may differ, depending 3 on the CW pitch setting. 29. [NOTCH] SW (SSB) 4 (Default: Auto/Manual) • OFF : The displayed frequency does not shift. • ON : The displayed frequency shifts when the op- 5 Select the Auto, Manual or Auto/Manual notch filter to erating mode is changed between SSB and be used for SSB mode operation. CW. 6 • Auto • Manual : Only the Auto notch filter can be used. : O nly the Manual notch filter can be 35. CW Normal Side (Default: LSB) 7 used. • Auto/Manual : B oth the Auto and Manual notch filters Select the sideband used to receive CW in the CW normal mode between LSB and USB. 8 can be used. 36. KEYER 1st Menu (Default: KEYER-Root) 9 30. [NOTCH] SW (AM) In the CW mode, select KEYER-Root or KEYER- 10 (Default: Auto/Manual) SEND as the menu that appears first after pushing Select the Auto, Manual or Auto/Manual notch filter [KEY](F-4) in the "M1" screen (Menu 1). 11 used for AM mode operation. • KEYER-Root : Memory keyer menu appears first. 12 • Auto : Only the Auto notch filter can be used. • KEYER-SEND : Keyer SEND menu appears first. • Manual : O nly the Manual notch filter can be used. 37. External Keypad 13 (Default: OFF) • Auto/Manual : B oth the Auto and Manual notch filters can be used. Turn the external keypad ON or OFF for keyer memory transmission. 14 31. MN-Q Popup (MN ON) (Default: ON) See page 18 for the equivalent circuit of an external 15 Turn the manual notch filter width display ON or OFF. keypad and connection. 16 When this item set to ON, and the manual notch filter is selected with [NOTCH], the manual notch filter width • OFF : The external keypad does not function. 17 appears on the function display. • KEYER SEND : In the CW mode, pushing one of external keypad switches transmits 18 32. BW Popup (PBT) (Default: ON) Turn the IF filter passband width and shift value dis- the desired keyer memory con- tents. 19 play ON or OFF. 20 When this item set to ON, and the [TWIN PBT] control is rotated, the passband width and shifting value appear on the function display. 21 88
![](/manual_guide/products/icom-ic7410-instruction-manual-6fdb052/95.png)