Icom IC-M510 Instruction Manual - Page 80

Navigation, Starting navigation

Get Icom IC-M510 PDF manuals and user guides View all Icom IC-M510 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

9 OTHER FUNCTIONS ■ Navigation The transceiver assists you to navigate to a selected destination. L The function works only when the transceiver is receiving valid GPS signals. L The function cannot work while in the MOB mode. NOTE: The Navigation function is a supplemental aid to navigation only, and is not intended to be a substitute for primary navigation equipment. D Starting navigation There are 3 ways of setting a destination using NAV , selecting in the AIS list, and selecting in the Waypoint list. NOTE: A popup screen is displayed when the vessel arrives at or near the destination. To stop the function, push any key. L When the Audible Alarm function is set to "ON," an alarm also sounds. (p. 60) Using [NAV]: 1. Push NAV on the operating screen. • The "Waypoint" screen is displayed. 2. Push [▲] or [▼], or rotate [CH/ENT] to select a waypoint. 3. Push Start to start navigation. • The plotter screen is displayed, and the transceiver starts to navigate. • is displayed on the plotter screen. 4. Push the Software Key for your next operation. Selecting in the AIS list: 1. Open the list screen. [MENU] > AIS > Target/Danger/Friend list 2. Push [▲] or [▼] or rotate [CH/ENT] to select an AIS target. 3. Push NAV . • "Start navigation. Are you sure?" is displayed. 4. Push OK to start navigation. • The plotter screen is displayed, and the transceiver starts to navigate. • is displayed on the plotter screen. TIP: You can also start navigation in the details on the AIS target. 1. Repeat steps 1 and 2. 2. Push Details , [ENT], or [►]. • The "Details" screen is displayed. 3. Repeat steps 3 and 4. 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
67
9
OTHER FUNCTIONS
■
Navigation
The transceiver assists you to navigate to a selected destination.
L
The function works only when the transceiver is receiving valid GPS signals.
L
The function cannot work while in the MOB mode.
NOTE:
The Navigation function is a supplemental aid to navigation only, and is not
intended to be a substitute for primary navigation equipment.
Using [NAV]:
1.
Push
NAV
on the operating screen.
• The “Waypoint” screen is displayed.
2.
Push [▲] or [▼], or rotate [CH/ENT] to select a
waypoint.
3.
Push
Start
to start navigation.
• The plotter screen is displayed, and the transceiver
starts to navigate.
•
is displayed on the plotter screen.
4.
Push the Software Key for your next operation.
D
Starting navigation
There are 3 ways of setting a destination using
NAV
, selecting in the AIS list, and
selecting in the Waypoint list.
NOTE:
A popup screen is displayed when the vessel arrives at or near the destination.
To stop the function, push any key.
L
When the Audible Alarm function is set to “ON,” an alarm also sounds. (p. 60)
Selecting in the AIS list:
1.
Open the list screen.
[MENU] > AIS >
Target/Danger/Friend list
2.
Push [▲] or [▼] or rotate [CH/ENT] to select an AIS target.
3.
Push
NAV
.
• “Start navigation. Are you sure?” is displayed.
4.
Push
OK
to start navigation.
• The plotter screen is displayed, and the transceiver starts to navigate.
•
is displayed on the plotter screen.
TIP:
You can also start navigation in the details on the AIS target.
1.
Repeat steps 1 and 2.
2.
Push
Details
, [ENT], or [►].
• The “Details” screen is displayed.
3.
Repeat steps 3 and 4.