Intel SHG2 Product Guide - Page 26

Installing Memory - server board motherboard

Get Intel SHG2 - Server Board Motherboard PDF manuals and user guides
UPC - 735858152891
View all Intel SHG2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Installing Memory The SHG2 Server Board contains six 184-pin DIMM sockets. Memory is partitioned as three banks. DIMMs must be populated in identical pairs. 3B 2B 3A 2A 1B 1A Figure 6. DIMM Locations OM14558 The SHG2 server board supports up to six 2.5 V, ECC, DDR 200 or 266-compliant, registered SDRAM 184-pin gold DIMMs. A wide range of DIMM sizes are supported, including 128 MB, 256 MB, 512 MB, 1 GB, and 2 GB DIMMs. The minimum supported memory configuration is 256 MB, using two identical 128 MB DIMMs. The maximum configurable memory size is 12 GB using six 2 GB DIMMs. The SDRAM interface runs at 200 MHz; however 266 MHz memory can be used. The memory controller supports 2-way interleaved SDRAM, memory scrubbing, single-bit error correction and multiple-bit error detection with Chipkill capability that allows the system to continue to run even in the event of a multi-bit SDRAM failure. Memory can be implemented with either single-sided (one row) or double-sided (two row) DIMMs. ✏ NOTE Use DIMMs that have been tested for compatibility with the server board. Contact your sales representative or dealer for a current list of approved memory modules. Check the Intel Customer Support website for the latest tested memory list: http://support.intel.com/support/motherboards/server/SHG2 26 Intel Server Board SHG2 Product Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
26
Intel Server Board SHG2 Product Guide
Installing Memory
The SHG2 Server Board contains six 184-pin DIMM sockets.
Memory is partitioned as three
banks.
DIMMs must be populated in identical pairs.
1A
1B
3A
3B
2A
2B
OM14558
Figure 6.
DIMM Locations
The SHG2 server board supports up to six 2.5 V, ECC, DDR 200 or 266-compliant, registered
SDRAM 184-pin gold DIMMs.
A wide range of DIMM sizes are supported, including 128 MB,
256 MB, 512 MB, 1 GB, and 2 GB DIMMs.
The minimum supported memory configuration is
256 MB, using two identical 128 MB DIMMs.
The maximum configurable memory size is 12 GB
using six 2 GB DIMMs.
The SDRAM interface runs at 200 MHz; however 266 MHz memory can be used.
The memory
controller supports 2-way interleaved SDRAM, memory scrubbing, single-bit error correction and
multiple-bit error detection with Chipkill capability that allows the system to continue to run even
in the event of a multi-bit SDRAM failure.
Memory can be implemented with either single-sided
(one row) or double-sided (two row) DIMMs.
✏
NOTE
Use DIMMs that have been tested for compatibility with the server board.
Contact your sales representative or dealer for a current list of approved
memory modules.
Check the Intel Customer Support website for the latest
tested memory list: