Intel SHG2 Product Guide - Page 49

Installing the Processor Wind Tunnel

Get Intel SHG2 - Server Board Motherboard PDF manuals and user guides
UPC - 735858152891
View all Intel SHG2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

9. Position the retention clip over the plastic tab and engage the retention clip end-slot over the plastic tab (see 1 in Figure 31). Note that the slot in the clip provides room for side-to-side motion while engaging the retention clip slots located at each end. 10. Press downward on the retention clip ends over the plastic tabs on the retention bracket (see 2 in Figure 31). 11. Install two retention clips on each processor you install. 2 1 2 OM14368 Figure 31. Attaching the Heat Sink and Retention Clip Installing the Processor Wind Tunnel The following instructions apply to the Intel SC5200 Base Server Chassis and reference chassis installations. If you are installing your server board in the Intel SC5200 Hot-Swap, Redundant Power Server Chassis, DO NOT install the processor wind tunnel. The ducting in the Intel SC5200 Hot-Swap, Redundant Power Server Chassis eliminates the need for a processor wind tunnel. 1. Install processor wind tunnel center section over the heat sink / processor assembly. Note that plastic tabs engage the tabs on the retention clips. Upgrading OM14369 Figure 32. Attaching the Wind Tunnel Assembly 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Upgrading
49
9.
Position the retention clip over the plastic tab and engage the retention clip end-slot over the
plastic tab (see 1 in Figure 31).
Note that the slot in the clip provides room for side-to-side
motion while engaging the retention clip slots located at each end.
10. Press downward on the retention clip ends over the plastic tabs on the retention bracket (see 2
in Figure 31).
11. Install two retention clips on each processor you install.
OM14368
2
2
1
Figure 31.
Attaching the Heat Sink and Retention Clip
Installing the Processor Wind Tunnel
The following instructions apply to the Intel SC5200 Base Server Chassis and reference chassis
installations.
If you are installing your server board in the Intel SC5200 Hot-Swap, Redundant
Power Server Chassis, DO NOT install the processor wind tunnel.
The ducting in the Intel SC5200
Hot-Swap, Redundant Power Server Chassis eliminates the need for a processor wind tunnel.
1.
Install processor wind tunnel center section over the heat sink / processor assembly.
Note that
plastic tabs engage the tabs on the retention clips.
OM14369
Figure 32.
Attaching the Wind Tunnel Assembly